Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear Voice Expert,Let me explain the issue. The phone is configured in the call manager and in VLAN it is up but still it shows as unknow. i tried performing factory for 7940 phone.Unplug the power cable from the phone, hold down the # key, and then ...
Hi guysWe are going to deploy dot1x access with LSC certificate for our IP Phones and since we are talking about more than 400 phones we are thinking about a bulk procedure to install them.Is there a way to check if LSC installation has been deploye...
HiI have no experiance in Cisco 2901 router configuration. I am using VIC2-2FXO (2 analog ports) to connect to VOXEO Prophecy voice portal. As in VOXEO documentation described , I have to define Dial Peer to the IP address where Voxeo Prophecy Instal...
voice translation-rule 2 rule 1 /^\*48\(..\)/ /+151483447\1/voice translation-profile 4SRST translate called 2call-manager-fallback secondary-dialtone 0 max-conferences 4 gain -6 transfer-system full-consult timeouts interdigit 8 ip source-address 1...
Customer has 10.5 CUCM and Unity CxN and PCCEUsers have been imported to CUCM from LDAP and then imported into Unity from CUCM. Both systems have password and pin policy's of user cannot change to avoid admin overhead with resetting passwords.Custome...
Hello Everyone,I have two sites: HQ and Site C. I have one Cisco 9971 at each site. HQ site is having CUCM 9.1.2 whereas Site C is CME. HQ router is configured as CUBE. The two phones talk to each other via CUBE. Whenever I make a call between two p...
hi Team,I've a basic query which revolves around CUCM Group on SIP Trunk, The group the Phone is in & the IP addresses configured on dial-peer on VGW. Below is the scenario: CUCM 10.5 I have IP Phone in CUCM group A : servers in Group are 10.10.100....
I have setup a sip trunk to a third party server that works as a voice directory server.this works fine, however what I would like to do is in the case of the 3rd party server being unavailable, I would want cisco to forward the call to a receptiond...
Hello,I'm setting up some 2960's that will be used for cisco phones. On my access ports I'm using 'auto qos voip cisco-phone' for automatic setup of qos.On my trunk ports I'm using 'auto qos voip trust' to allow qos tagging to follow the frames to th...
Dear Expert,I have a IP Phone 7965. My IP Phone 7965 clock is losing time with NTP Server.However, All other IP Phone7965 is synchronized with NTP Server.Only one IP Phone7965 is not synchronized.In a normal time a Clock Time Zone is JST 9, But Now T...
I am running a system clustering multisite over WAN (HQ, Site 1, Site 2). Each of the sites are connected to the HQ via WAN.In each of the site, i have 2 subscribers and in the HQ, i have 1 Pub and 2 SubsI originally have 1 MPLS circuit which works p...
Hello,Request someone to help me to understand below license terms.Part NoDescriptionQtyCP-8831-EU-K9=Cisco 8831 Base/Control Panel for APAC, EMEA, & Australia1CON-PSRT-CP8831K9PRTNR SS 8X5XNBD Cisco 8831 IP Confer Phone w/ controller4CP-8831-DCU-SSp...
Hi Guys, We are starting to now use the ATA 190 for a basic cordless phone in our sites as the ATA 187 are end of sale... I have an issue where one these 190's that hold (hookflash) is no working. If I repeatable press it, it will work about 1 out of...
I am working on a CUCM 10.5 1.11900-13 HA cluster. When the subscriber server was turned off to performe maintenance on the physical host the publisher server became unresponsive. We could not log into the webpage and when we SSH'd into the server th...
I have a couple of users who say the speaker phone part does not work well. When making calls to an outside line they say that the party they call can not hear them when our users use the speaker phone. They tried calling again, and still, the part...
