Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello there,Does anyone know of a way of connecting/browsing to a CUCM on a VMWare session using a laptop which is not connected to a LAN?Obviously doing an ipconfig we can see the LAN is disconnected and we dont have an IP address;Ethernet adapter L...
Hi, guysI have the CUCM 8.6 iso, and Im trying to install it using VMware Workstation 9.0.2On the network configs, I want to use GNS3 as my default gateway and I use a router on GNS3 as NTP server.Can anyone please help me on this?I dont know how to ...
Hi,We should migrate Cisco IP Communicator user settings from Windows XP to WIndows 7. That means not to configure again application, just when the same user login to Windows 7 will have same setting as on Windows XP.I'm planing to use USMT 5.0 for t...
Remote office. CallManager 8.6 at the main office and a 2901 router in the remote office H323 trunk between the offices. Extension dialing works. Calls into the office via outside line works. Calls from that office to the outside world, however, the ...
Hey team, I have been configuring a CUCM 8.6 in a customer. All features are working properly, but I would like to configure the FAC for each user use a private password. So, FAC is configured in the "route pattern" and all user will use the same pas...
Hello guys,I have configured BLF Speed Dials in CUCM v9.1 but I'm still not able to configure them from the users web access (they just don't appear in the ccmuser web access), does anyone know if it is posible in this new version???With regular Spee...
Good day,Have the 2851 cisco with cme 7.1I have to dial-peers to external trunks. To one dial-peer calls going through prefix 9 and another to prefix 5. We have 5 sccp phones that should can go only through dial-peer with prefix 5. So I want to chang...
Hi Everyone,I wanted to check if there is any way to pull a report (from cucm) which gives us the number of users currently logged in from the cisco end user pages to manage their phones - is there any way we can find this out? Thanks!Atul
Hello,I have a 7961 phone with the following loads: SCCP41.9-0-3S.I want to install the phone with a customer who has CME but with a lower loads file: SCCP41.8-3-2S.loadsWill this cause any issues? Initially the phone didn't boot at all, so i connect...
Hi to everyone,Does know anyone if there is a 3d party IPhone SIP Client compatible for UC500 that works over VPN?Thank you!
In all of the examples I have looked at in the QoS SRND and the Medianet Campus QoS Design 4.0 guide they show inbound VoIP being policed at 128kbps and inbound signaling being policed at 32kbps on the ingress switch port. None of the examples reall...
Hi,Until now all the sites used u-law where i worked. I have a requirement where one country telco uses a-law standard. Is there any configuration that i need to put in place on the VG to support a-law or the ISDN PRI does the voice encoding
Hi I have a CUCME 9.5 and I am unable to save the config from the GUI. I get the message other telnet session active. I seem to remember this was a bug in earlier versions is this the case in 9.5.
hi all, I have cisco 6921 Ip phone installed in my network, when ip phone received 4 to 5 voicemail ip phone was got hang and MWI notifications is auto blinking.kindly help for this issue
HII all, I Have set up mobility profiles for metting rooms, and are workign fine the problem is I do not have an option to logout of the profile once signed in I am using Cisco IP Phone 7940 series. I must be missing a setting somewhere can somebody ...
