Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I have a CUBE that is sending an INVITE to a proxy, and in some cases the proxy just sends the call back the CUBE.This causes the following error:*Nov 29 22:20:37.652: %CALL_CONTROL-6-CALL_LOOP: The incoming call has a global identifier already pr...
Hi I would like to transfer from a CallHandler to a DN via Caller Input I can't get it to work, i tried with (Transfer to Alternate Contact Number) but it only works with a huntpilot Press 1 for 7897441 (DN)Press 2 for 7897440 (DN)Press 1 for 7890010...
Hi, I am new to cucm, if anyone can help me to create these route patterns.The range of numbers is:908-685-6660 ~ 6679, 908-203-2560 ~ 2599, 908-203-2400 ~ 2439-Any help will be appreciated.
I am looking for confirmation of the multiplatform software on this ATA so it can register to the control hub. My question is to confirm what firmware included or do I need to upgrade it to the MPP firmware?
Hello All, I have a Cisco ATA 186 with a fax connected to it. I have been at this for weeks. This is through sip service. I am at a dead end. I can receive faxes but can’t send. The fax machine dials and you hear it connect then drops with a communic...
Can't able to hear old voice messages. To listen up those messages, clicking on 3 as required to hear older messaged in 8945 Cisco IP phone. When I press option 3, the phone doesn't give me the old messages. On the contrary, it waits for me to leave ...
I need some assistance for caller ID associated to 911 dialing. We have CUCM 11.5(1) and use CER for 911 dialing. All phones have an external phone number mask assigned. Same config that's been in place for many years, but just found an issue for o...
Will dvo feature will work without mobile devices? we need to implement that feature without mobile devices.
Hi to all,I have a Cisco 7945g a friend gave me as he gave up trying to upgrade it so now its my goI have a tftp server setup as a dhcp server and the phone connects directly to the computerI am upgrading the phone to sip firmware 8.5.2 unfortunately...
hello to everyone, our client complaints that when they call their customers and hear their AA,they press their choice without success most of the time. they describe it as "the device does not accept our choice and we continue to hear the AA till th...
HI all,I have got sip number from numbers from SIP provider so far the translation rules profiles and dial peers are as below:voice translation-rule 1rule 1 /022799232/ /501/!voice translation-rule 2rule 1 /5../ /022799232/and translation profilesvoi...
hi i am sorrenrino ciro i have a router 2901 cme 7.0, i configured a dial-peer .T that goes on the pstn and i configured the g0 / 0 interface as pppoe which is connected to the internet, but i have a problem sometimes the pstn line and busy I did a d...
I have a Cisco ATA191-3PW-K9 V04 with firmware 11-1-0MSR3-9 dated June 9 2019 installed.I'm having trouble locating a later firmware. I believe I have found the right stuff but I'm not confident.The link to what I found is on this page. Can anyone he...
My cisco phone keeps going into outbound calls. While i am waiting for a call it goes in and out of outbound call. And while i am on a call it will go into outbound calls and hang up on the caller. I am not having any luck with the IT department were...
Hello, I recently purchased a Cisco 7942G with SCCP firmware and installed SIP Firmware 8.5(4) on it successfully. I also transferred the dial plan and SEP Config files with it. When the phone restarted, I expected it to configure its IP then enter t...
