Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, trying to figure out how to have one user control two softphone devices that are located at different sites. Current config is:Site A:Publisher, IM& P primary, Sub and Unity serversDevice DN #1 on Media grp, device pool, CSS and Partition conf...
Hi, Ive been working on a lab setup for CCNA. I have a 2901 with the UC license applied and a SIP provider.I have outbound calls working on the phones in the lab and im now trying to get inbound dialing working. I have a DID setup at the SIP provider...
Help!I know it's a long shot but I was wondering if anyone had similar issue in CUEAC?Our receptionist this morning complained they couldn't login into attendant console.After investigating, it turns out, the "ARC CTI Server" windows service on the s...
This is the debug data:Aug 9 12:14:56 ATA192-MPP local1.debug vsock: SIP_getIpBySrvHost2(83) line(0) Resolving(proxy.sip.sapo.pt) port(5070), rc=4Aug 9 12:14:56 ATA192-MPP local1.debug vsock: SIP_getIpBySrvHost2(122) line(0), type=2Aug 9 12:14:56 ATA...
i need support in below task.i have 7 audios1- welcome note/welcome in Arabic language, for English press 2 (if 2 is not pressed it should continue with arabic language)2- for sale dept. press 1, for complaint press 23- same as 2 but in Arabic langua...
Hi allassume we have 2 branches A and B. In each branch we have third party voip gateway( new rock brand) with sip trunk integeratin with cucm( in head quarter).my question is:when phone A( connected to fxs port on newrock voip) call phone B(connecte...
Hi All, We have recently upgraded our Call Manager to 12.0.1.219, and now when I try to add a VG204XM gateway I receive the following error when I try to configure the FXO ports: " Access to the requested resource has been denied, The attempted a...
I'm looking for some help with an issue that has come up.Some VPN users that are using Cisco Jabber to answer calls are reporting that they are either unable to hear the person on the other end of the call, or that person can't hear them speaking. I ...
Im looking for the part number for the power supply for 8821 Desktop Charger part CP-DSKCH-8821=. It did not come with the power supply.
HiSome help required please. I need to set up an analogue phone on a 4321, with 2 port FXS NIM installed. Its all set up (config below) but there's no dial tone, and the cable status on the voice port is 'not connected'. I've turned the rj11 cable ba...
HiWe have a CUBE and we need to modify the Remote-Party-IDNow it looks like this: Remote-Party-ID: "personal name" <sip:123456789@X.X.X.X>;party=calling;screen=no;privacy=offWhat we want: Remote-Party-ID: "123456789" <sip:123456789@X.X.X.X>;party=cal...
Hi there, Is there any document available that would tell me how the media negotiations during a call and how can I read the CUCM logs to verify. Also how to we get to know if the calls has failed due to media resources issue by checking the cucm l...
Hello everyone, I have noticed in Cisco Jabber, phone services on the app it shows the CUCM server address, which is against the company policy, how this issue can be sorted and is there anyway to use OTP services to login?
I need to deploy SRST FALLBACK on local router ISR4321 version 16.6.4The CUCM cluster is in mix mode version 12.5.1.13900-152The customer have 8811 and 7821 IP phones all the phones are on secure profile TLS (encrypted) When I test the SRST only n...
Hello, I'm new to forum and to cisco.I'm a user of Vodafone in Greece that provides me FTTH 100/10 with Data, Voice and TV. Few years before I bought one 2801 Router and one 2901 in order to play with for learning.Vodafone serves all this services f...
