Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, Q1: I have configured IP phones in CUCM GUI but it says IP phones are not registered. CUCM v11.0 Phone models: 8865, 8851, 8811, 7821 and DX-70. Q2: And also i had a backup I couldn't apply and restore it Please assist me on this? possible pro...
CUCM 12.5 We are planning to deploy Mixed-Mode CUCM to our secured environment, however, our IT admin does not allow TFTP protocol to be used in our network. Any alternative for TFTP protocol for phone configuration? Thank you.
Hello Cisco Community,Is it possible to register an external extension on Cisco Jabber, so that PSTN calls should be dialed/received directly on our Cisco Jabber Softphone?If this is possible, then can we have some documentation links so that we can ...
Hello,I have been trying to set up a call handler. I have successfully set up transfers for caller input. I need one more thing. When a caller does not select any option in the call handler i need it to go an extension. how can i set this up.
We have an ATA 190 that will no longer register. It stopped a month or so ago. There are no link lights on phone 1 or phone 2 ports. I can ping the device. It has firmware version 1.1.2. I tried some other suggestions from the community but they didn...
I have given a task to re-IP all the Cisco voice phones from 192.168.x.x addresses to 172.22.x.x addresses. Site has Cisco 3925 router running dhcp pool for the phones. My questions are---can I create new dhcp pool (slightly different name than exist...
Hi Gents ,I'm facing issue in CUCM System version: 6.1.2.1000-13 , I am unable to took backup auto or manual so please check below :admin:show diskusage inactivelogThis command can take significantly long time,and can also effect the system wide IOWA...
A little later in April, I am planning to upgrade both Cisco Call Manager and Cisco Unity to version 12.5.1 from our current version of 11.5.1.13902-2 which we upgraded to in 2016 or so. I am curious if anyone has any recommendations about doing thi...
Recently upgraded to 12.5.1 and took the opportunity to replace the self signed certs with CA Signed certs.For the Call Manager / Tomcat and IPSec , certs. Also added root ca/issueing ca to the trust store of these.Everything (and Jabber) works perfe...
Hi All, I have a question regarding licensing for CUCM. Suppose on CUCM 11.5, I have 20 users with a phone each and only 2 CUWL licenses. I can configure a common user and assign it to all 20 phones and be license compliant. When I upgrade to 12.5 Sm...
Hi,I have a Cisco Unified CM Administration, System version: 8.6.2.20000-2.I would like to know if it is possible to retrieve call from external after internal extension, recipient, does not answer, with a Cisco IP Phone 7912, and if yes, how can I d...
Hi, Just wondered if anyone had found a browser or other setting to prevent this annoying error message? Most of the time you just hit Save again and it works, but for some elements when you first hit save and get the error, it randomly removes som...
Hello All I built a sip trunk to a telephone provider's PBX. They ask me sent " invite" include both G711ulaw and G711alaw. I checked" Media Termination Point Required" . There only is G711ulaw in "invite" message. Do you have any experience abou...
Cisco 9951 phone is not registering with cme 9.1. When I run debug ccsip messages, I am getting below errors Received:REGISTER sip:10.20.1.1 SIP/2.0Via: SIP/2.0/UDP 10.20.1.95:5060;branch=z9hG4bK2bc83d5cFrom: <sip:4500@10.20.1.1>;tag=64e9502f6135003a...
Hi all, I've been configured Phone Template with SURL on the 2nd button.When I'm adding new phone from template it's taking the SURL just like It's supposed to be,but when I try to add another phone from template there Isn't SURL, It's gone from the ...
