Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all,I have a number of 6921 phones which fail over to SRST mode,However no system message is displayed on the phone to indicate that the phones are operating in SRST mode.The Router is a 2911 with IOS version c2900-universalk9-mz.SPA.152-1.T.bin. ...
Hi.I would like to get a better understanding of how the built In switch works In an IP phone. As I understand It: One port connects to a main switch and Is a trunk port. There Is an Internal access port that connects the voice vlan to the phone. ...
OK, not sure why this isn't working. I have a CME 8.1 system with a B-ACD setup to do basic call queueing.According to the documentation, you're supposed to be able to setup an "out' for the caller to press a key and get out of the queue prior to th...
I have just installed some 7925's on our network. Every ringtone on them sounds exactly the same as it does on a 7975, except one (my favorite =P) which is the CTU24 ringtone. Could there be any reason why this one ringtone does not work properly on ...
Recently I added 2 new subscriber (s1 & s2) on a 6.1.5 cluster. I made a CCM Group with these subscribers and change the DevicePool for diferent test phones. These phones were registered locally in s1 but were unregistered in publisher. If change the...
Hi,Please anyone suggest me why in CIPC->Preferences->Network tab Device name and Tftp server options are not editable..?Um new to cisco voice plz help me..Thnks in advance,Harish
Dear all,now I have telephony line: ISDN PRA (30B+D) and PSTN gateway is AVAYA.Now, instead AVAYA I want to connect telephony line to Cisco 2921 with voice card:1 Channelized (E1 or T1)/PRI portHow can I start to configure cisco as pstn gateway?Regar...
Can I assign a certain name to the Caller ID number So that when that Customer calls again I can see its name on the phone not his Caller IDCan I use the Directory service for that purpose?
CCME extension assigner was dialed today to swap out a broken phone, it normally works fine. The following is now occuring.Dial the extension number, greeted with "Welcome CME EA, enter password". After dialing the first digit of the password (or any...
hi,i have a 2901 with 15.2(2)M and one PVDM3-16 installed. I try to get working an ad-hoc conference but when i enter the commanddsp profile 1 conference maximum session <0-0>0 sessions? --------------------------------------------------------------...
HiWe have a DDI range where a few numbers need to be re-directed to a QSIG trunk using more specific dial peersNow we have the "problem" that on the incoming dial-peer the DDI range is translated to our internal numbering plan.is there a way to exclu...
HiWe have a H323 gateway and we need to re-direct/deflect certain DDI number to a QSIG trunk on the same gateway.In ohter words, certain DDI numbers will go to IP Phones but a few numbers in that range need to go to the legacy PBX via QSIG (or other ...
Hi We have some 5-6 IP phones not getting registered to CME . " Registration failed " is coming to these 5-6 phones . we have enough licenses . TFTP is reachable . here are the config i have checked in CME ip dhcp pool VOICE_VLANnetwork 10.1.0.0 2...
Trying to do some things on CUCM 8.6.2a with CIUS tablets. Can't find documentation on how to do the following things:1. While on a video call, how to you get the CIUS tablet to switch over and use the REAR camera on the call (i.e. how to switch be...
Hi there,I have H323 gateway with FXO card, When I am making a call from CCM to PSTN through certain port number, call gets out but I hear call cancelation beeps. When I connect analog phone to this line I can make the calls successfully. what could...
