Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,We have installed Cisco 2901 router as CME for one of our customers. This will be a dedicated CME serving near about 40-45 phones. There will be no integration with CUCM or any other UC devices. All phones are registered to CME. Attached license f...
Hello,This is probably a pretty basic question for this forum but I don't know how you do this. Can someone please advise how I would go about to set up configuration backup via FTP for CUCM 8.5?Thanks,Adil
How do I display the full software version? I'm only familiar with the linux based systems. Thanks!
Hi all,I would like to have a copy of hard drives of my CUCM 6.1.5 for store it in another place.I found this article related to CUCM 7.1.2 where is indicated the procedure to change a failed hard drive: http://www.cisco.com/en/US/docs/voice_ip_comm/...
Hi all,I'm looking for your help about a problem I'm experiencing on a customer site.I configured a SIP Trunk with a "virtual" destination ip adress that load-balance to two "physical" ip adress (for a fax server cluster).Since I do that, the outgoin...
Hello,Our ELIN numbers are getting "wardialed" on a regular basis. The call gets routed to CER, but there is no 911 match. The call then gets routed to our onsite police through the onsite alert setting (And are getting pissed). When there is no 9...
Hi All,Im new to Visual voicemial. Most of user in my site are facing the problem in visua voicemail. When i was looking into this issue i found that the file ".jad" is not downlading and getting the below error intermitently. Sometime im able to dow...
Hi,I have CUCM 7.x in HO and SRST in branches. The communication between the sites is via G.729. Centralized call processing model is used. When we try to conference between sites it does not happen. We are not using any hardware conference bridges a...
Hi,I have call manager 8.5 installed and a route pattern that route all calls to the gateway. No restrictions. I can make local calls , international calls and calls to mobile phones but I can't call 5-digit numbers. I get external line with 0 and wh...
When I ping from local router to IP phone the situation is like this:<font color=red>Sending 100, 100-byte ICMP Echos to 10.1xx.x.x, timeout is 2 seconds:!!!!!.!!!!!!!.!!!!!.!!!!!!!.!!!!!.!!!!!!.!!!!!.!!!!!!!!.!!!!!.!!!!!!!!!.!!!!!.!!!!!!!.!!!!!.!!!!...
Dear Cisco support communityHow do you set correct VLAN for the Cisco softphones, the version number is 8.6.1.0. We are using them under Windows 7 Pro 64-bit SP1.We have around 10 phones which keeps on joining a wrong VLAN, but in the Cisco softphone...
Hi Guys,I would like know if the Cisco allow to download version 8.6 demo. My Customer have a one CUCM in LAB version 7.1.3 and would like first test this version, after then He bought the product.Thanks,Wilson
Hi , Hope everyones doing well. I have a very urgent issue here , where a sudden request has come up for a CUVA setup between locations in US and France . I have got it done but would kindly like to confirm the cameras that are supported by CUVA. In ...
Hi All,i have arround 6 remote VPN locations they use remote access through cisco VPN clientthe main Firewall is ASA5510 and i have the network gateway is sonicwall TZ 210 the problem is that the remote locations they can login and make internal call...
Hi,Am using cisco 2911 router - C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M4,Below config works fine, but i can reach only operator & i can dial by extension. i cannot create param aa-hunt1 for dialing individual digits. How to achive tha...
