Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,In CUCM 7.1.3 we registered the Nortel 1120 SIP Phone. Phone is registred & from there we able to calls the numbers internally with in the cluster.If i dialed some external numbers i'm getting fast busy reorder tone.In CUCM logs we are getting "SI...
I have an ata 187. I would like to configure it, and I don't see it as a drop down choice for a new phone configuration. I only see ata 186. Where do I install this device. Should it come up in the drop down menu?
Hi,we are planning to upgrade our call manager from 6.1 to 8.6 on the MCS7800 publisher and subscriber servers. can we do the upgrading without compromising the current configurations and also retataining the current unit licences? also, does 8.6 sup...
I know there are licensed features in IOS 15.x I have a show ver and I see what I have "Perm" listed.Is there a limit when it comes to SRST licenses and is there a way place to check on this? IE, # of phones or DNs, etc.
I get "the server encountered an internal error" when logging into Phone Designer on CM 7.1. Anybody know what this error is from? Is there a setting that needs to be flagged to allow a user to login to Phone Designer?
hi all,is ESW a requirement for ordering UCSS ?in the ordering guide is seem to be that way.but it is not clear if that's what is ment.regards Ron
I have a customer that is upgrading from CUCM 5 to CUCM 8.5, we found that the branch routers running SRST with IOS version 12.4, from the compatibility matrix I found that he should have minimum IOS 15 so that the SRST could be compatible with CUCM ...
Hi,Can anybody list requirements for Personal and mobile communicator? I have a CUCMBE with general license. Is that enough or CUWL is needed.
Hello everybody,I plan to integrate Exchange 2010 UM with Callmanager 6.1 for voice mail, i want please to know : - If exchange 2010 is compatible CUCM 6.x - What about Exchange 2010 and CUCM 6.x MWI support, it work or not ?RegardsMohamed
Dear All,I have purchased cucm 8.5 with preinstalled media kit.Can anyone please provide me the guide to start the installation from the beginning.I will be very grateful.regards,Malik.
Hello guys,I would like to know if it's possible to upgrade the firmware just for a small group of phones and not all the phones for a specific model.Besta regards,Filipe
Hi,We are going to upgrade ios in 3925 SRST enabled voice gateway from 15.0(1)M6 to 15.1(1)T because the existing ios does not supports 69XX IP Phones in SRST mode . We have CUCM 7.1.3 , Unity 7.0 and CUE 8.6 in our setup.Whether the new IOS 15.1.(1)...
I use a Cisco 2811 as E1/SIP Gateway for Asterisk. Outbound call works well but some incoming calls fail (20% !). Here is the logs:*********** CALL OK *****************Sep 7 21:40:05.494: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x1CD3 B...
I am Unity Connection 7.1 and we had voicemail to email previously configured and working. It has however stopped working. There are only a handful of users using this but thoseusers had an IMAP connection configured to connect to UNity to download...
I`m currently testing EM redundancyEnabled EM on one or more servers A- B and you create a single IP Phone ServiceShut own the EM Service on one of the Servers A or B then mobility will still work as long as the Phone can access the IP address in th...
