Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
hello,We need to do a MANUAL redirect (or a call transfer?). Is mean, we need when the operator leave the site for something (go to the bathroom, drink cofee, etc) he cand redirect the incomming pstn calls to a provisional extension. Is possible? how...
I have a PBX connected to CallManager. If it possible for me to add a "Calling Name"? If a call originates from 3337901 I want the station name to say East Desk. Any way to do that?Also, can we add a mask, so that when someone calls outbound it ch...
Is there any way provided we have the proper licensing to connect third party NEC Dterm IP phones to a cucm without going through an NEC PBX?
Hi. Is is possible to configure seperate ring tone for each user based on the caller number or caller name in cisco ip phone 7906G. please guide me how to proceed with the same if it is possible.thanks and regardsRajesh
Hi,how is it possible to configure it?I am running 15.1.1T and it is CUCME 8.0.It says that it supports pickup group but i cannot configure it or use it.Under the dn, i have included a pickup-group but still nothing when pressing the key.
IP Communicator 7.0.4 connecting to CUCM 7.1.5 via CVPN 5.0 over a verizon wireless card is the environment. One way audio is the result. The reason is obvious: CUCM 7 shows the IP Address of the CIPC client as the same IP address of the server cau...
Hello,We have an install including 2 CUCM 5.1 servers (Pub and Sub), about 80 phones, and one voice gateway (with 1 PRI, and 1 T1 CAS circuit). All endpoints register with the Sub as their primary server with the Pub being the backup. Almost all in...
Greetings:I just noticed that CUCM 8.5 has support for phone type cisco E20 (former Tandberg E20), so i tried to register my E20 to the new cluster like the others cisco models, the problem is that I cant make it work in this way.The E20 works great...
Hello,we have some UC 8.X appliances (CUCM 8.X, CUCCX 8.X, ...).Which are the CLI or web commands to retrieve all the the information for their License MACs?This to have all the data for a new installation in case of a disaster recovery (and to obtai...
Hiwe are using CCM 7.0 and configure MGCP gateway with E1 PRI. users encounter the caller ID issues when dialing out to external phone calls, the IPT display the company mainline number eg. 29967688 for Hong Kong rather than the DID / extension numbe...
Currently, when a caller calls into our contact center after hours, we forward the call to a third party voicemail box. The problem is that the original callers number is not passed, instead it's the extension which was called. Is there a workaround ...
OK - sometimes this stuff just doesn't work like I expect it to for no apparent (to me) reason. Platform is CME.I want to send outgoing calls to a specific number via h323 to a remote site. I have several dial-peers, but I believe that only two are ...
Hello,A client of ours is getting a Warning message whenever they access the CAR (CDR Analyzing and Reporting) Homepage. The Warning states as follows:------------------WARNING-----------------------* Last run of CAR Loader is unsuccessful, please ch...
Hey Everyone,I am working with a client on an NTP syncing issue. While looking into it, I noticed that in the output of utils ntp status command, it shows that it is synchronized to local net at stratum 11. The NTP setup on CUCM Pub is as follows: Pr...
All,What is the CSS in Voice Mail Pilot used for? Will the Voice Mail Pilot number initiate any calls?Thanks,
