Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi there,I got a question regarding this top:If there is no Media Resource Group List (MRGL) has been assigned to Device Pool, IP Phone (Device) and User Device Profie (UDP), what will happen if a call has been put on "Wait" (MOH) or a conference has...
Hi,I upgraded a CCM 4.1.3 to CUCM 6.1.3,Upgrade was successful all the phones except 7912 take the new loads. I have a problem with 7912 phones which is getting registered with their old firmwares,but not the new firmware listed in CUCM 6.1.3(In devi...
Hi,We have a customer that has a number of users with DECT phones that connect via Kirk IP system back to the CUCM. (So the DECT handset registers with the Kirk box, and the Kirk registers with the CUCM). Telephony all works fine, in that users can c...
Hi I have CCM ver 7 , once i go to phone then go to Directory Button then go to Corporate Directry , is showing me Directly error " Error , contact administrator " , note this problem on all phones . please can you help me ASAPthanks
I have two IP phones, 7911 and 7906 in CME. I want to change firmware from SCCP to SIP. How can I make the change?I have already the file cmterm-7911_7906-sip.8-4-4.cop but I don't have the procedure.thanks
Hi all,I have to integrate CCM 6.1 with Unity Express for voice messaging !!! can any one share the document for it ...Thanks in advance Regards
Hello folks I have some issues with dial-peersI have a 2811 running MGCP as the primary protocol and is registered to CCM 6.1(2).for emergency calls, we are routing the calls through 2 local FXO ports, the ports show as registered in CCM, however in ...
Hi Guys,As I can to do blocking a directory number to that it blocking Redirect Call to external phone or celular phone? Any rule in the forwarding external calls?Thanks,Best Regards,Wilson Santana
HII just want to know if anybody has used Cisco 28xx series router with E1 modules and PVDM2-64 for voice termination and pass it to GSM Channel bank via ISDN PRI E1.I will be using it h323 voice gateway with voipswitch.Is this reliable hardware as c...
Does anybody know the OID or how I I can SNMP poll my CCM (4.1.3) to collect active PRI channels on my gatways?Since I'm MGCP I figured I need to poll at the CCM and not the Gateway(s)I've skimmed over the CISOC-CCM-MIB and saw nothing.
I have a 2811 router with an MFT card and PRI. Inbound calls only display "Unknown Caller" on the phones for caller ID.An ISDN Q931 debug shows all 10 digits being sent to the router.
I am trying to connect Cisco 2821 voice gateway to Harries PBX via E1 PRIPBX team told me they configured it with ETSI configuration What ISDN switch type should I configure in my 2821 gateway to communicate with the PBX ?RegardsMohamed
Under CallManager 6.1 can I restart the Disaster Recovery/Master Agent services via CLI/SSH? rather than CCMService?http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/drs/7_0_1/DRS_CUCM/drsag701.html
Hi,I have been testing a scenario for a customer and have ran into this issue.We have a remote site with a PBX that connects into a gateway via 4 FXS ports. The gateway is using MGCP signaling. Our intention is to use G729 between CM and the remote s...
hi there is one way audio in the calls generated or originated from the cme's phone, the physical connection is through an E1, and this problem also happens with a FXO port. I think that something is happening with dsp, what do you think? i sincroniz...
