Activity in Technology and Support
can not boot into 3.2 ISO image from the VM-based
trying to migrate our ISE nodes to 3.2 version in a VM-based infrastructure, I am trying to boot VMs into the ise-3.2.0.542a.SPA.x86_64.iso image as obtained from Cisco's software download center but I keep getting the attached error. It is worth no...
aaa server radius dynamic-author
SW2(config)#aaa server radius dynamic-authorSW2(config-locsvr-da-radius)#client 192.168.100.210 server-key Test123SW2(config-locsvr-da-radius)#client 192.168.100.220 server-key Test123Those commands means that we set AAA server (ISE1 and ISE2 in this...
Web Auth 9800 Redirection Issue
We have recently migrated to Cisco Catalyst 9800 and we having an issue with a captive portal/web authentication. in the old 5508 we point to the same portal with no issues. However, the portal doesn't work on the new WLC. We have a publicly signed c...
Enter rommon NCS540 XR
Hello,I need to enter in rommon to change the confreg because I cannot use "conf t" in the actual configuration.I tried during booting to press "Break" from Putty terminal but is not able to run into rommon.My intention was to check the following lin...
IOS IPv6 CoPP
I'm trying to configure IPv6 access for a BGP session and I want to control this through CoPP, to have more control plane security on my Cisco router with IOS, I did an initial configuration and it continues to accept connections from IPs that I didn...
How can I Setup Email Alerts for Queue Overflow in Webex Flow Designer
We are currently evaluating Webex Contact Center as we consider transitioning away from UCCX. In our existing setup, if there are more than three people waiting in the call queue, an email is automatically sent to the supervisors to alert them. I've ...
Cisco Finesse "send error report"
Cisco Unified CCX AdministrationSystem version: 12.5.1.11001-348 (SU1-ES03)Where does one get access to view the error repot that get generated when you click on "send error report" with the Finesse web page?
Beginner - How to Enable TLS for SMTP on UC Apps
I've been asked to enable TLS for SMTP on all UC apps - CUCM, CUC, IM&P and CER. I'm a complete beginner, and aside from some documentation for Unity I can't seem to find anything at all regarding enabling TLS for SMTP on these platforms. Is this eve...
Stacking IE3400 by Fiber, Is it possible?
I have two IE3200 switches and I want to do a stack with these, someone knows how I can do it? is this possible?
Adding a Physical NIC to UCS/VM
Overall Objective:Need to make physical nic on rackmount Cisco UCSC -C220-M5SX available and assign to VM (Windows Server 2019) residing on a Cisco USCB-B200-M5 that exists in a Cisco Chassis that is connected through a Fabric Interconnect. Cisco UC...
Image upgrade failed - rommon now
Hi all-I have an old 6509 with a SUP720 that I seem to have killed. I was trying to upgrade the code.Before the reboot, she file systems looked like this:and the sup-bootdisk: directory looked like this:I changed the boot line in the config from b...
Multicast Routing with Layer3 switch and Palo Alto Firewall
I don't deploy multicast often so I wanted to ask about MC configs as a sanity check. I have two Palo FWs each with a layer3 interface/gateway for separate servers. The FWs are two L3 hops away from each other. There are two L3 Catalyst 9300 switc...
Cisco 3560X Capacitor Failures
Hi all,I teach at a networking academy at a community college and we have a few donated 3560X switches supplementing our student lab. Six are deployed in pods. The room has adequate climate controlIn the last 10 months we have had two fail, announcin...
Configuring MFA Using Cisco ISE and Microsoft Azure MFA
Using Microsoft Azure MFA for multifactor authentication within Cisco ISE.
Not seeing the gateway ip in attached topology while pinging from Pc2
HI all,I have this topology where I am doing static everywhere.I have a doubt here, I am doing static from 192.168.10.2 (gateway -10.1) to 192.168.30.2. Also, I am doing per packet load balancing on R1 and disabled cef. Now, when i am doing a trace t...
| User | Helpful Count |
|---|---|
| 147 | |
| 127 | |
| 99 | |
| 96 | |
| 64 |
