Unified Communications Infrastructure

Renew CAPF Certificate in Mixed Mode & NAC environment

Hi,Wondering if anyone has experience regenerating a self signed CAPF cert in a ISE/NAC environment? We have the CAPF cert uploaded to ISE to authenticate the phones on the network. I'm reading what happens when you re-generate the the CAPF cert and ...

Resolved! What is different for Embedded vmware 7.x on BE6K/7K ?

Now, Cisco embedded vmware have 2 version Basic Plus and Enhanced.What is different for those 2 versoins? BE6/7K-VIRTBASP-7X = Cisco BE Embedded Virt. Basic Plus 7x, BE6K/7K onlyBE6/7K-VIRTENH-7X = Cisco BE Embedded Virt. Enhanced 7x, BE6K/7K/CMS1K ...

Resolved! How to Get a List of All of Our Active Devices

Hi. I'm trying to get a count of all of our active VoIP device types. I stress the word active, so I'm looking for a count of device types that have an IP address or have a status (registered with a server). We have thousands of phones so a manual...

Resolved! Modify Invite sip-header ip From (parameter)

Hi Community, My provider (ISTP) is asking me to send the Invite, in this SDP message to appear the IP (189.204.181.121) of the interface that is connected to the service in the from parameter.CUCM (10.210.160.17) <---> (10.210.50.250) CUBE (189.204....

Resolved! How to login for local enabled users(service accounts mostly) when SSO is enable on CUCM(11.5)?

We have enable SSO for CUCM but now we have a few accounts(local users) ex: Service Desk Admins who used to be able to login to CUCM/user to change call forwarding as per their requirement. Now they are not able to login. Is it possible if i have the...

cisco cucm version 8.0.3.20000-2 ISO required

Could anyone share the cisco call manager required image 8.0.3.20000-2 and the upgrade path images as i cannot find them at this portal Thanks for your support in advanced

Resolved! Incoming CallerID via Translation Pattern

Hi AllAll incoming calls via SIP Trunk go to Translation Pattern (5555555 -> 2022). 2022 it is Hung Pilot for 3 DN's. During incoming call to 5555555, I see on the phone screen 5555555 for 2022. How to remove "for 2022)?

Resolved! LDAP user is not Synching in.

Currently having issues synching new employees in AD to CUCM. Has anyone ran into this, or know some troubleshooting steps? Before I would just perform full synch and the users would appear, but about a week ago after creating a new user, they would ...

jabber SSO windows problem

hi friends, i currently install cucm 11.5, cup 11.5, and Microsoft-ADFS-Server2012R2,sso saml is enbaled on cucm and cup, sso test is ok and its working,i can login as sso way on cucm and cup but when jabber windows wants to sign-in, will find servic...

Resolved! CUCM Sub Node - Backup Restore

Hi Team,Quick question. As my LAB is not accessible today, I would like to have your help here.I need to re-build 1 CUCM sub node and add into existing cluster. Once this server is built and part of the cluster.How can I restore the backup only for t...

BT Netrix migration to Third Party IPC Unigy with existing 12.5 CUCM ENT.

BT Netrix migration to new Third Party IPC Unigy - ENT. Project 1,500 End Users with existing CUCM 12.5 and NICE - NTR Voice Recording. Any docs or Base config regarding Third Party SIP, and H.323 VG configs would be greatly appreciated.

ISDN-6-LAYER2UP/LAYER2DOWN

Hi all,I have a cucm 11.5 intgrated with gateway ISR4321 with protocol H.323 , in this gateway i have a BRI .The problem that i have the somtimes the calls not be work , after i checked the gateway i found that interface BRI change state UP to Down y...

"clock source line primary" disappear after a lack of power

Dear all,we have configured, on a ISR4331/K9, Cisco IOS XE Software, Version 16.07.0 Cisco IOS Software [Fuji], ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Versi on 16.7.1, RELEASE SOFTWARE (fc6), the following set of commands: controller E1 0/1/...

Resolved! CUCM/CUC compatibility with vault secrets (pki/ssh)

I am, trying to integrate CUCM/CUC authentication with vault PKI or SSHit is possible? I think being a Linux OS it is possible, but I can't find the option with the command line. PKIhttps://www.vaultproject.io/docs/secrets/pki SSHhttps://www.vaultp...

Resolved! HDD

Are these HDD compatible with BE6KHD300G10K12NSAAL14SEB030N SCSI 12Gand what if the HDD is new, but 5 years old

Unified Communications Infrastructure

Forum Posts

Renew CAPF Certificate in Mixed Mode & NAC environment

Resolved! What is different for Embedded vmware 7.x on BE6K/7K ?

Resolved! How to Get a List of All of Our Active Devices

Resolved! Modify Invite sip-header ip From (parameter)

Resolved! How to login for local enabled users(service accounts mostly) when SSO is enable on CUCM(11.5)?

cisco cucm version 8.0.3.20000-2 ISO required

Resolved! Incoming CallerID via Translation Pattern

Resolved! LDAP user is not Synching in.

jabber SSO windows problem

Resolved! CUCM Sub Node - Backup Restore

BT Netrix migration to Third Party IPC Unigy with existing 12.5 CUCM ENT.

ISDN-6-LAYER2UP/LAYER2DOWN

"clock source line primary" disappear after a lack of power

Resolved! CUCM/CUC compatibility with vault secrets (pki/ssh)

Resolved! HDD

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

CUCM Constantly Disconnecting TCP Socket

listChange output

"Service Manager is currently busy" After Restarting Cisco XCP Router

Secure SIP integration between CUCM and IM&P...

Monitoring/alerting for issues with Unified Messaging and Speechview

jabber - delete message from external sql

IM&P VM Resizing ways

Is CUCM 12.5 SU6 Comatible with expressway X12.5

CUCM 12.5 ESXI Support

CSR8000v Demo CUBE