Hi Forum We have recently bought a few Cisco ISR1100 router with POE on the first 4 ports. They cannot feed the old 7960/7940 IP phones, but have no problems in feeding and Cisco 2802 AP. I suppose this has something to do with the non standard way t...
Forum Posts
Hi all, I hope someone can point me in the right direction of how I can troubleshoot and figure out an issue we are currently experiencing (bare with me, my cucm knowledge is still fairly basic).Environment: CUCM and CCX 12.5We have a small "call cen...
Is there any way to allow Finesse/UCCX agents to switch between Jabber DN and Remote Destination to receive calls? I want to use the Device for Calls>Edit Number field in the Jabber app to choose where they receive calls.I have configured Extend and ...
We have a device that's configured on our Nortel PBX that when we call the number configured it will tell us what number we're calling from. It works for Nortel and Cisco phones.We hope the Nortel PBX will go away but would like to configure the same...
Resolved! Caller ID on DN Variable
I've been searching for something, and I'm curious if anyone else here knows of a way to do it. Maybe my google-fu just isn't good enough...Is there a way to use an Assigned User's (to a directory number) Name as a variable to set the Caller ID.Basic...
Resolved! Cisco IP telephone SNMP
Hi I have two question related to Cisco Ip telephone. 1) I have Cisco ip phone 6901, No of quantity is 598, this model does not has SNMP feature. Is there any way to get snmp feature for this IP telephone by paying extra cost to cisco ?2) If its not ...
Hello all, Our phone system is experience suspicious outbound calls, all of them are international calls. I tried to trace the calls information from CUCM logs for all suspicious calls without any luck. I can see the call first called into our main n...
Hello all,I wanted to see what users' voicemail PIN setting is "Does Not Expire"-checked. Totally around 300 users with voicemail box. I tried both Bulk Administration Tool and Cisco Unity Connection Serviceability > Users Reports without luck. I don...
Resolved! CME 11.5 SIP 8841 Registration issue
Config below, simple setup following guide from Cisco here https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/manual/cmeadm/cmebasic.html#concept_A2BD5A1412FA4256A7059097E08CBD03 On how to auto-register SIP Based phones. ...
We have a number of General Dynamics Sectera vIPer phones (ver 6.1 SCCP) connected to ourCUCM server (11.5). They work fine in non-secure mode. They do not work with CAPF, but by manually creating certificates using openssl (and common name CP-7961...
We need to change the admin password for over 50 Webex and Telepresence VC codecs on CUCM. This is a huge manual work.Seems Bulk update of phones does not support the admin password update.Is there another way to update the admin credentials in bulk...
Hello,I am looking to getting the Device Type added to our Cisco CUCM. I went and downloaded the COP file from Cisco Repo and went to the Cisco OS Admin and did install/upgrade. I got a sucess and rebooted the tftp service. However I do not see the ...
I am trying to display photos in CUPC. I was told I could store them on a web server as a jepg. Then in AD set the Wep page field to the address of the photo (http://<web server><filename>.jpeg) Then in presence admin set the CUPC photo attribute to ...
Resolved! address book
hi I have a 2901 CME 7.0 router I have IP telephones registered in sipv2 but I have a problem the telephone number directory does not come out what should I do? Thank you.
I want to connect noise cancelling headphones (Bluetooth) to a Cisco 7940 desk phone. Is this possible, if not, what desk phone model do I need.
