Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi experts,So our setup is that we have CMEs at a remote locations managing 7962 SCCP phones for our customers. We have a CUCM in the core used as a SME to handle calls between the CMEs or to/from the outside PSTN. Between SME and CME are the SIP tru...
After upgrading to the DPC3008, I have only 1 downstream channel and 1 upstream channel. I know there is one solution on the Comcast forums. However, there is only one Engineer there that knows how to escalate this issue to to get the problem resol...
Product: DPC3939B Question: Is the SIP ALG just enabled on the 2 voice lines or is it enabled on the 4 ethernet ports as well?
Having issues with a gateway that is setup as MGCP with 3 PRIs coming into it. Recently, there have been reports with two of the DIDs (that the client is aware of currently) where the call drops. In the Q.931 debugs, I see a mandatory information e...
Hi,We have a testbed CUCM network. In the network we have one publisher, and two subscribers. We are intended to use CUCM publisher for administration purposes only and the devices are registered to other subscribers accordingly via two device pools....
Hi,I recently upgraded a customer from CUCM 7.1 to 10.5 and replaced the 7960 handsets used by their UCCX agents with 7841 handsets. The handset upgrade was driven by the need for a Built-in-Bridge for MediaSense recording.They have now come back to ...
Hi everybody I have issues in my company ..I added new branch and give to him extension number. But the issue the staffs new branch can't not taking together by ip phone.Even though they can call other branches.
Hi,If i have 2 Unity Connection Servers running HA of each other, is it normal that the other one will not show backup? i have tried restarting DRF service and restarting the server which has the not responding status but still getting the same after...
HiWe have CUCM 9.0 on HQ and H323 Branch router with FXO and IP Phones registered on CUCM.FXO voice port config is below on every FXO port. Also outbound call works fine.voice-port 0/1/2 no battery-reversal cptone ID timeouts call-disconnect 3 timeou...
Hi community, the next great issue at this installation:See the attached screenshot, i´m running into an unrecoverable error within the installation routing from CUPS 10.5 on a UCS-Server, BE6k.It happened several times, i did:Remove the machine comp...
Dear Experts,I am upgrading CUCM from version 6.1.3.3000-1 to version 10.5.2.First I did physical to VM conversion by taking backup and restore to new CUCM installed over VMware.Since there is no direct upgrade path, I upgrade the CUCM to version 6.1...
Dear all,we migrated to 10.5 and we are using IPMA service and application.The service works as expected, but on the assistants phone the detault screen of the 7960 is the "Service"Screen showing the IPMA Service login./logout status. When there is a...
Hi mates,Just a thought besides complexity in achieving the same. We have following appliances;1. PUB2. SUB13. SUB24. CUPS5. CUC6. CUCCE7. SIP/H.323 Gateways (leaves MGCP aside)Upto physical installation of each of the above appliance on different or...
Hi,Having a problem getting the Connected Number Display to update after a transfer, and was chasing more information about whether this is properly supported in v9.4 of the SIP firmware and how/what the phone does for these updates?Using the phones ...
Hello,We are currently using phone-preffered call recording, but we have some phones we need to record over SPAN. We would like to use gateway-preferred recording. I have setup SIP trunk to recording enabled gateway 2911 and did external call to phon...
