Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, we have an CUCM 9.1.2 and want to connect an DX80. The data sheet of DX80 says that it is possible. But I didnt found a device package for CUCM 9.1.2 to support the DX80. I've downloaded the DX80 firmware and was able to install it successfully, ...
Hello, I am new to Call Manager and to VoIP phones in general. Currently have Call Manager version 6.1.4. We have a specific extension (example 2911) and this line is setup as the second button on all of the phones in an office. We are using Cisco IP...
We're using UCCE 7.2 and are moving to 9.0 in a few weeks. One of the questions that we have had is how to determine the termination point of a call. I'm looking for a way to report through either the HDS or call manager whether the agent or the ca...
Hi , One of our department is facing an dead air issues randomly only for few extensions. I trying to know what are the criteria we need to check on call statistics to justify that the issue is with the Network or not and how much the value should be...
Why CME 10.5 claimed to support the CP-8831, but that is no type 8831 and must reference the 6921?http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/requirements/guide/cme105spc.html For example:voice register pool-type 8831 xml-config maxNumC...
Hi friends,While configuring Device Pool to be assigned to MGCP gateway, which all parameters under Device Pool are relevant to MGCP gateway? I'm sure not all parameters are relevant.Would appreciate if you can redirect me to any doc which mention ab...
I'm around trying to restart from the CUCM several phones however not sent restart think it's some bug someone has happened something similar and restart the clouster not the bug was corrected
At Wed Apr 17 01:00:27 IST 2013 on node 10.9.10.5; the following SyslogSeverityMatchFound events generated: SeverityMatch : Critical MatchedEvent : Apr 17 01:00:08 duhacu01 local7 2 : 285: XXXXXXXX.XXXX.XXX: Apr 17 2013 00:00:08.689 UTC : %UC_CERT...
I'm needing to order more phones for my company due to company growth. Our most common phone model is the 7945g and for all intents and purposes that model has been solid with few issues for us and I do not hesitate to reorder that model again. I als...
What is the stable version of the new CUCM 10.0 or 10.5?Can you upgrade direct from 8.6 to 10.0/10.5?We are currently running 8.6 on IBM blade center, is Cisco going to require me to upgrade to 10 on UCS?
Hi guys, I set up CUCM on a VM. And am having problems with my ip phone not getting firmware from the CUCM TFTP server, i did a factory reset on the phone and its now stuck in an endless loop of rebooting, it gets an ip address, but then it says "ter...
Hello,I have got 2 CUCM servers (Publisher and Subcriber) in system version: 8.5.1.10000-26.Publisher crashed (disk failed) and now all operation goes throw the Subcriber.I could not find answers to the following questions:What is the best practice f...
Hi Team, What would be the main difference of installing CUCM on MCS, Rack mount and Blade server. Take an example with 3000 VOIP end points.
Hello,I understand the unity connection global setting for using first vs last redirecting number to make a call go to the different voicemail boxes when a DN is forwarded to another DN. We have a special scenario where DN 6115 is CfwdAll to 6116 an...
Hello All, We have installed a CUBE to communicate with the SIP provider, the setup goes as followed: Call Manager => CUBE => SIP Provider , The CUBE has 2 interfaces: LAN & to SIP provider. The network for the SIP media is not a directly connecte...
