Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi everyone, We are facing an issue with voice gateway login via putty. We are using SSH for login but since last week we can't login but the gateway is reachable when we try to ping. We are getting "remote side unexpectedly closed network connection...
My org is presently running CUCM v10.5.2 on premise and is preparing to migrate our voice service to a cloud VoIP provider. I am working to document our existing setup so it can be duplicated as much as possible. Here are my questions. Is there a w...
From the Main Campus call cannot be initiated whereas from the branch side call can be initiated. Moreover, we are also observing spoofing on the interface of the Main Campus router
Colleagues, good afternoon!There is a scheme PBX-PRI-CISCO-SIP-CISCO-PRI-PBXIs there an analogue of the voice-class sip options-keepalive functionality that exists in VOIP dial-peer for POTS dial-peer?I need to get the busyout state on the remote sid...
Hai I have a problem about Router which is Smart License "pending" status, when the VG router device was at my customer's office the problem was that access to cisco.com / internet couldn't, it resulted in a RENEW_FAILED log and a "Pending" status. T...
Hi,After double clicking on the installer [CUACS_Setup.exe], the installer is asking for the details [Like FQDN/User ID/Password] before installing the application. Is there a way to skip this part? If not how should I proceed with installation [I do...
Hello,Looking for a quicker way to do the following:This week we will have to pigrate 350 IP Phones from a CUCM cluster (to be dismissed) to another.In order for the phones to register onto the new cluster.We have to reset the security settings (see ...
Hi,I am working with Performance Monitoring Tool.I recently ran into an issue in the CUCM environment that my Call Manager server collapses due to too many sessions (for example when I run the command "show open ports regexp tomcat" for example, I ca...
HelloI set up a 8865NR phone including 3 extension units. I defined 66 lines that are defined as a hotline.In order for the hotline to work on the extension unit it is necessary to change the phone to enhanced line mode but I'm having a problem. The ...
Hello Experts, We have a Cube with SIP trunk with Cisco Webex Calling and ITSP the Call flow is as the following:-ITSP >>the unify Firewall >> CUBE >>the unify Firewall >> Webex calling Our Issue : when we call a user on webex calling we just hear ...
I have Cisco SME with below issues:Incoming external calls to IP Phone working properly.Outgoing calls from IP Phones to PSTN working properly.but now when I forward my Ip phone to external number and try to call to my Ip phone from external, I get b...
I have noticed that my Cisco switch does not see my IP communicator via CDP. I'm using CIPC version 8.6.4 and my switch is a WS-C3850-24P running Cisco IOS XE Software, Version 16.09.06As you can imagine this is going to be a problem for Cisco Emerg...
Hello All, A client of mine complained they experience lags while making calls on their IP phones. When you dial a number, it takes almost a minute before the call connects. This wasn't the case before now. Note: This does not affect all the users. K...
Hi all, Will auto config for Cisco handsets be effective on all branded handsets? We have a small site who have just started using Ericsson-LG handsets. I have put these devices on their own VLAN but I cannot see any improvement in call quality after...
I am trying to figure out a way when a user dials a number say 911 it will automatically do a conference and dial another number to conference our security console onto the call as well.Would CUCM even be able to do this? Or would we need Emergency R...
