Hi All,Please can someone confrim whether any expansion module is available for CIPC.I havent come accross anything like this.Thanks
Hi All,Please can someone confrim whether any expansion module is available for CIPC.I havent come accross anything like this.Thanks
Hi All We have CUCM 8.6.2, at the begining its installed as 8.6.1 then its upgraded to 8.6.2, now we need to add another subscriber for this cluster, what will be the procedure to add new subscriber, if we installed 8.6.1 then there will be DB miss m...
Can EM be configured on Cisco IP Phones (added on CUCM 7.1.5) but without adding any line in this phone?
Dear All,when we press the message button we are hearing the below message and why is that ? "tell the last and first name " then press #we are using cuc 9 for voice mail and AA and even the AA is not workingplease help
Cisco 9971 phone buttons setup as Speed Dial BLFs, User gets the call, hits transfer, hits the speed dial,call is not getting transfered. Instead, it is esablishing another call and there is no way to trasfer the call, also does not appear the tra...
Hello all,Please is it possible to make some particular sets of IP telephone not able to make any outgoing calls but allow incoming calls only?I use CUCM 6.0 and i dont seem to get where i can enable this feature on the CUCM, can anyone put me thru o...
Hi thereI am looking for some help in replacing a Subscriber in our CUCM 9.1 cluster. A server had a disk fault and after replacing the faulty parts I am now looking to rebuild the subscriberI am following this document:http://www.cisco.com/en/US/doc...
hiwhile i am try to configure new phone in my router 3925 it show me phone not register. but i have some phone from the same model which work fine and i still have license and the space is availabe and the firm wire is there. also...
I am trying to work on a lab with HQ and remote site.HQ phones are getting registered with CM but remote site phones are not..I am attaching the gw configs. remote site phones are getting ip from dhcp and tftp server IP. Remote gw is able to ping HQ...
Hi All,I have just completed a restore of a CUCM 9.1.1.20000-5 Publisher and Subscriber, all seems to be ok however replication is broken bewteen the two servers.When I run "utils dbreplication runtimestate" from the publisher, it fails with the foll...
Hello,I'm trying to figure out which wireless headset to buy as a gift for someone who uses Cisco IP 7941 at work in a call center. Not sure how the Cisco phone works, but they are currently using a wired headset that automatically pick up calls with...
Hi Everyone,I have a site with a BE6k running CUCM 9.1, 8-port 3560 POE, with 3 phones.1 x 7975, 2 x 6961.The users were saying they hear choppy audio on the 6961 phones, but not the 7975.Upon investigation I notice a v.high amount of jitter on the 6...
I'm using UCM 9.1 with Unified Mobility (xfer to alternate number) with good success if I follow a typical call flow:Inbound call -> Ext -> Rings deskphone x seconds -> Rings mobile phone -> Answer mobile phone -> hangup -> Resume call on desk phone....
Guys,very quick one I not seen before.Just upgraded a single phone to SCCP45.9-3-1SR2-1S, before we do a mass upgrade just to check it out.On the phone http page i see Version*SCCP45.9-3-1SR2-1S*What does the * indicateThe current default load is SCC...
Dear All,I have Cisco CME 2951 and want to have voicemail for users. So how to check whether I have licenses for voicemail or how I can order the same.Let me know if config needed.Thank You,Abhisar.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-11-2025 09:37 AM | ||
02-10-2025 04:39 AM | ||
02-07-2025 02:45 AM | ||
02-04-2025 01:17 PM | ||
02-04-2025 06:55 AM |
User | Count |
---|---|
3 | |
2 | |
2 | |
1 | |
1 |