Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello.I have Cisco Presence server with version 8.6.5.10000-12. Now I got a message on the screen:System was operating in Evaluation mode and the license has now expired. Please upload the relevant license file in order to allow the system to run i...
7942g excellent call with ncp500, but then i need transfer to another telefone number nothing happen. I can hold a call, even when the push transfer the first line hangs and I can return to it after talking on the other line. But transfer i can. I pu...
Hi allhope you can help. need advice/solution from community.have scenario where, users dial a national number. once call connected, requires new telephone number to be sent.first i dial:0811288XXXX,After call connects, IVR prompst for dialed numbe...
Hello,I have the file TSPSingleLinex64-2-2-0-8.exe dated from 16/11/2010.Can't find a newer version (I this version is difficult to find on download area)Do you know if there is a newer version ? (I use a CME)Do you know if it exist a tapi client fo...
At precisely 20mins of any outgoing call, CME just kills the call. You dial again and have another 20mins. Any idea what this might be related to?
I have a UC560 which generates tremendous traffic in our LAN. Switches go like crazy like they receive a huge load of broadcasts. When I disconnect it from the network all switches go back to normal operation. Is there any way to find out what genera...
Hi voice team, I´d like to integrate my microsoft lync 2013 with my CME 8.6, using the same extension already configured on CME. How can i do that?Thanks.Thiago
I've got an issue when trying to log into Extension Mobility on a 6921, Extension Mobility is enabled and the MAC of the phone is registered with Call ManagerWhen powered on, the phone boots and registers with the Call Manager. A DN profile is loaded...
Hey guys, having some issues in the lab running 9.1 CUCM and CUC.I have a SIP trunk setup from CUCM to CUC. I have imported my users, and created mailboxes. Problem is when I call a DN and get forwarded to VM I get the enter your PIN instead of being...
Hello Guys,I have a strange behavior in a CUCM 8.6 environnement. Times to times, on random phones the corporate directory is no more listed. I have to reboot the phone and all is ok.I go round in cycles since weeks and I didn't find any clues about ...
Hi all,I am configuring CUE 7.1 with CME. I can dial to voice mail number but busy tone responding. Pls review the log:CUE1# show trace buffer tail Press <CTRL-C> to exit...5011 10/17 11:37:59.829 ACCN EXMG 0 STANDARD-worker-8:Finished work 3626 10/1...
My Cisco 2921 came shipped with two preinstalled VWIC3-2MFT-T1/E1, and I had no problems adding it as MGCP gateway to my new CUCM BE6000 version 9.1. However, even though both VWIC3's appear nicely at show inventory, they seem completely dead. All LE...
Hi,I just want to know that below rule would remove 9 from incoming number. Now i am using CUCM 7 with h323 gateway. Telco is sending last 4 digits and poiting to CTI route point. Now at above scenario, whats the use? and where shall i call that prof...
Dear All, Can we pull out the CUCM full configuration in text format ?Actually one of My customer wants CUCM' confiuration in text format to check feasibility to add CUCM to "Device Expert" like switches, router etc.Below is the over...
Hi All,We are running with CUCM 9.1.2 & LDAP integration is enabled. When we tried to do the Manual sync for one of the LDAP directory & it immediately disappear from the Directory list in CUCM GUI & all the user went to Inactive state.While we veri...
