Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all, I´m having troubles to upgrade CUCM 14SU2 (14.0.1.12900-161) to 14SU3 (14.0.1.13900-155). I get this error: component_install|File:/opt/cisco/install/bin/component_install:936, Function: execute_shell_cmd(), /usr/local/cm/script/cm-dbl-instal...
Hi, I have a site that recently changed their switches to Fortinet 424E-FPOE 421w, but now their 8851 KEM's are not working. My question is, what is the power needed of the 8851 with a KEM installed. Thanks
Setup: I've got a approximately 20 Cisco IP 7841 phones connected via PoE to the domain. These phones are DHCP enabled and receive their IP Address from a Windows 2016 Server. The parameters(phone number, label etc) for the phones are configured on a...
I am using a Cisco landline phone at work. I am hard of hearing and wear hearing aids, but still have trouble hearing on this work phoneIs there an amplifier available to purchase. If so do I need to know the model number of the Cisco phone that I am...
I have been noticing Jabber 14.3.1 will shut down on it's own. When i re-open it I'm still logged in.Is there a bug with version 14.3.1?
Hi gentlemen, Is there a way to have a DSP calculator for PVDM-4.https://www.cisco.com/go/calculator is a 404-error Page not Found. Thanks.
Hi All,We have a publisher and a subscriber and 2 offices. Currently all phones are registered to publisher. How do i force 1 office to register to publisher and the other half to register to subscriber? CUCM version is 8.5Thanks
After a lot of trouble shooting I have discovered that I can get an Cisco 8851 to drop the network connection right after I press the Sleep key on the keyboard. This is becoming a problem as because if the computer sleeps for too long the phone will ...
Hi I have 20, 7811 phones all working fine and i added 5 new phones but the 5 new phones they have a problem. The problem is after registering all 5 on my server once they recive a call it would be instantly cut the moment i pick up the phone. any r...
Hello,I'm running CUCM 12.5, CUP 12.5, CUC 12.5, UCCX12.5 and I want to upgrade to 15.0I'm reading Upgrade and Compatiblity Guide.I have HCS UCM, HCS Unity Connections Smart licenses running until 2025 with no Version mentioned.Can I just Upgrade CUC...
Hello,We currently have 2- Cisco CUSP 10.2 and we have notification that the product is EOL with no replacement. Does anyone have a work around to remove the CUSP or equipment to replace the CUSP? Let me know if you have any questions. I sent config...
Hello,I have an ISR 2911 with the IOS 15.3(3)M5. This gateway is configured to allow SIP Phones to register in case of a CUCM failure using the eSRST mode.Here is the configuration:voice register global mode esrst system message "Mode SRST" max-dn 20...
Hello all. We started having issues with outbound calls with a SIP provider. This below is the call flow: CUCM -> SIP Trunk -> Voice gateway -> SIP Trunk -> Provider On the voice gateway, I'm getting a disconnect cause=47. Viewing the logs, it see...
Hi all, I have to purchase a RJ21 cable to connect VG310, is there anyone who know is the female or male on the amphenol end? Cat3 or cat5 pair? Thanks, Eric
Hi,I am trying to find the best way for an Internet Subscriber to set her/his Voice Greeting.Our system is Cisco Unity 7!!Thanks-B
