Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Is there a way to insert a pause in the call forward all sting in Communications Manager 8.6?What we are trying to accomplish is when a DID is called the number will call forward the call to an outbound number, pause and then dial a few more digits. ...
Hi Guys,I would like know if there any documentation informing the best practices for configuration CUCM 8.6Thanks, Wilson
Redundancy: what is better / what is the diference ?1. redundant-host commandccm-manager switchback immediateccm-manager redundant-host 10.10.10.2ccm-manager music-on-holdccm-manager config server 10.10.10.3 ccm-manager configor2. two VoIP dial peer...
Hi, I would like to know if it's possible to setup a call forward when no answer with phone 7940G currently running application P0S3-8-12-00 (SIP).I know it's possible to call forward all calls and it's working well but it's not what I want.ThanksSam...
Hello,I am wondering if we can use Option 150 in our routers to point to more than 1 TFTP server. What we wondering is to have the Option 150 to point to our CUCM servers and to also point to our Singelwire Informacast server. We need to reach our ...
Hi guysI have 3 UCM servers | SIP trunk with Cisco SBC (HSRP) with SIP trunk to SBC Service Provider.The PSTN number is 2222-0000 to 2222-9999And we have 4, fours dial-peersdial-peer v 1 voipdesc ## TO SBC SERVICE PROVIDER##destination-patter .Tsess...
Hi,I have a client requesting that we use the dial-by-number directory handler to announce back the 10-digit DID of users prior to transferring the call. This way, the outside caller can take down the number and not have to use the directory handler ...
Dear everybody, I'm now using CUCM 8.6 with a publisher and a subscriberand about 1000 phones had registered to this clusterall the IP phones are using - subscriber as the primary active CUCM, and - publisher as the standby CUCMIf I am going to add a...
I have a SPA2102 connected with Line 1 to a phone (which works great) and Line 2 to a FAX. My fax machine is a Canon ImageClass MF4150. Firmware is 5.2.12. My VOIP provider is VOIP.MS.When someone tries to send a fax to this fax machine, I hear it ri...
Hi all,One of my clients has about 20 restaurants which each currently take deliveries individually (no central call centre). The set up is very legacy, each site having about 10 analogue lines in which they receive the calls. The problem is we canno...
Did not know where to place this one.But will the SPA525g2 work on a CUCM 6.1 our customer sent this back " The SPA525G is designed for UC500 only for SCCP mode and will not work in Call Manager asa SCCP phone.The SPA 535G phones will only work in SI...
Hi,Our customer purchased C3925-CMESRST/K9 ( as it comes with 25 licenses) he ordered 2XFL-CME-SRST-25 which makes it to 75 licenses.and i actived license by Router(config)# license accept end user Agreement.......Now my customer wants to check if al...
Hello guys! The scenario is the follwong: a 2921 as MGCP gateway and a CUCM8.6. Incoming calls work but outbound calls I get busy tone. Below is the debug ccapi:025361: Mar 4 15:12:22.583 UTC: //-1/CCAPI/cc_get_call_entry: CALL_ER...
HiCan anyone remind where where the setting is in CUCM or unity that says which mailbox is used when callforwarding into Unity i.e the origional called extension's or the forward extensions voicemail boxthanks
Dear TeamGood Day to all.Please advise if CME 9.0 supports auto-configuration for SIP phones. If yes, then kindly please send me the link to the document confirming the same.This is an urgent client requirement and would highly appreciate if you coul...
| User | Count |
|---|---|
| 8 | |
| 4 | |
| 3 | |
| 1 | |
| 1 |
