Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello. I have an issue where phones randomly appear to go out of service. I had to restart one of my gateways due to some maintenace yesterday and this is when the issue started. Basically I power cycled the gateway which is talking MGCP to my single...
Dear Experts Is their is any way to change the Extension numbers with new ones if yes could you please provide me the steps to chage the existing DID/Extension range 1xxx to 3xxx by using Cucm7.1.3 BAT for 200+ numbers.Thanks
Hi all, I found that then I configure a Call Forward All by pressing button in a phone, the CFA CSS of the phone in the CUCM will changed automatically. Is it should be like that? How can I make it does not change? thanks in advance.
Every time I dock the Cius in the dock it states that there is a software update and the Cius will reboot in 60 seconds unless the update is delayed. After rebooting while docked the Cius does not rompt for this again until the Cius is removed from ...
Hello there,We are performing upgrade of a firmware 3.6(6) ( last firmware) to the MCS 7835I2-K9 servers to a whole cluster containing of 7 subscriber and 1 publisher for version 8.0.3. I downloaded the ISO file from Cisco website ,burn it to Dvd wit...
Hi All, we have two GKs communicate over H.225. Call setup is successful and two endpoints communicate with each other, each one behind one GK. after about 10-15 min, call is dropped. after run debug in GK, I see following error message. if you have ...
Right now I am in the middle of a migration away from a bunch of old digital PBXs to a Cisco VoIP platform nation wide. I have my my CUCM cluster configured and most all of my big sites and contact centers done so now I am moving onto my smaller site...
Hi,I have a problem with Cisco 7911G phone.When turn on the the power at the moment the red lights are flashing and after it lights up only one green "Applications Menu".The display shows nothing.The phone does not get any address from a DHCP and TF...
Hi,Failing to geta a PRI working in Doha. Outbound calls failing with invalid number format. inbound calls also failing. Sure this is down to the ISDN plan / type. Inbound calls also fail - the setup message on q931 has plan type : ISDN Type:National...
Hi,I have supplied VWIC2-1MFT-T1/E1 and VWIC3-4MFT-T1/E1 for PRI configuration but when I am deploying the same customer is mentioning that he has G.703 as PRI. However on the same card unstructured E1 is not supported. How do I support the customer?...
Hello everyone,I saw online that the HP Proliant DL380 G4 was supported as a 3rd party server to install CM 8.6 on. I ran the installation CD and it says the hardware is not supported. Can anyone point me to a link that shows the exact specs for th...
What is the latest version of Data Migration Assistant (DMA) .Customer wants to migrate his data from call manager 4.1 to 8.6. The latest DMA version I could find was 7.1, does that work for call manager 8.6 as well ?Any help would be much appreciate...
We use Sprint as a switched long distance provider. Sprint is configured to prompt for a long distance access code when certain numbers dial long distance, and not prompt for others.Until I migrated from MGCP to H323, this worked fine. Post migration...
We upgraded from 5.x to 7.1(5b)SU5 last weekend and then did server rebuilds of 7.1(5b)SU5 due tp partition size limitations this week. 2 days after the server rebuild, it was found that on a 7942, we are getting a "error code 4, parsing error" when...
HiI am new to fxo cards and need some help setting one up.I have a Cisco 2610XM Router with a FXO and a FXS cards connected to a cisco call manger server. I have got it all setup apart from incoming calls.I want it setup so that if someone dials the ...
