Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Small ISP in central NY. I have 3 phone lines coming into my home. They are delivered via 2 x cable modems (2 x FXS jacks on each cable modem). I have connected 2 of the FXS ports on the cable modems to 2 x FXO ports on a 2811 router. I also recei...
Dear friends .. m sorry i think this has been discussed many times...the option which i am looking for is .. to have some kind of code on few phones.. which can help the lobby phone or phone in the public accesible are to have some restrcitions after...
Everytime we dock any of our Cius's they are forced to upgrade their firmware (they upgrade to the same version they are currently running). Has anybody else come across this issue?
Hi everyone,I have what I feel like is a basic issue that for some reason or another I can't solve today. I have an ISR 2821 router running CME 8.0 and what I'm trying to do is get one phone to register with it. The part I'm having an issue with is...
Hi, I hope you are all doing great.I would like to know how to configure an expansion module with SIP in CME. I actually have a 7965 and a 7916, the 7965 one is running SIP in CME 8.6. However I haven't found a way to configure an expansion module fo...
Hi,I have a customer running CUCM 7.1(2) who has two Cisco voice gateways each with one PRI and a Quescom GSM gateway with four SIMM cards allowing four calls. The Cisco voice gateways are configured as H.323 gateways and the Quescom GSM gateway is a...
Dear All,Is it possible to configure format of CDR records produced by IOS gateway like as CDR records with CallManager?Many thanks for any help.
We use Nortel IP phones (1140E), according to the Nortel documentation Voice media is tagged by the phones as DSCP 46 and Signalling as DSCP 40.Can someone tell me where i have gone wrong! On my switch (3750) i trust the DSCP and have the cos-dscp ma...
HelloMy scenario is as follows. CUCM is running v 6.1.2, although upgrades can be considered if SW release is a factor in the functionality. There are a number of MGCP gateways (with PRI's) connected to the CUCM. I would like to route out a partic...
Hello,I want to create a webpage from where the clients can click on a hyperlink and directly dial to a number.As i know we have 2 possibilities:1. Webdialer2. Click-to-CallI cannot find a good paper that can explain to me how to do this step by step...
in Cisco UCM release 8.6 how to learn visual voicemail version?İf visual Voicemail is same with Cisco UCM (call manager) how to downgrade visual voicemail versiton to 7.1. Because we have 7965,7945 ip phone models and this model is works with visual ...
Hello,I have a UC320w and i want to create VOIP and POTS dial-peer, is that supported ??What i noticed is that there is default dial-plan ( Like POTS dial-peer) for each region, but what if I didnt find my region ??And what about VOIP dial-peer ?Than...
Greetings! I have an issue with all of my [5] IPCC CTI route points. The issue is affecting all internal UC Manger [8.5.1] users. For example, an internal user dials 2020 [hits the CTI RP] and immediately the user sees the called number [202...
HiHow can I limit the number of incoming calls (5)transmited to PRIthis configuration is correct?dial-peer voice 1 pots destination-pattern 5... answer-address 5... max-conn 5 direct-inward-dial port 0/0/0:15 forward-digits all dial-peer ...
CUCM v 8.0.3.20000-2Voice GW 3925 Qsig link to PBXHi weird one here, got a qsig link to pbx can call back and forth no problem from the two units.However we have set the call forward no answer to a pbx extension (can call it fine from all IP handsets...
