Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Currently Being ModeratedMicrosoft OCS2007 R2 & CUCIMOC - Terminal Services???Hello,we have implemented Microsoft OCS2007 R2 for Presence in our Telephony Environment With Cisco Call Manager. The Microsoft Communicator has been installed on Citrix ...
HiWe have CUCM 8.6, we have created one user for IPCCX admin login on CallManager.Once we integrate CUCM with LDAP that local user deleted automatically from CUCM.Even we created same user in LDAP AD, that particular user ID is not appearing on CUCM....
Hi,I'd like to attempt a bridge upgrade for a CM 4.1(3) cluster (finally finishing at CUCM 8.6) but the customer no longer has the media for the version of Call Manager (service release 3).Is there anyway of obtaining these installation disks or is t...
Hello everyone, this is my first post and I tried to find an answer to my questions in other posts but didn't find any, I've been really trying to get this done but can't work out a solution.So this is what I'm trying to do:I have 2 remote sites and ...
Hi,I have a customer in the UK that has an older ISDN30 circuit that uses the British Telecom DASS2 standard. This pre-dates the ISDN30e service that is now commonly provided across Europe.DASS2 is not supported by the Cisco 3945 gateway that we are ...
Hi,how to find the firmware of IP phone 7931g whitch Compatible with Cisco Unified CME 8.6, on router 2921and how to install it ?
Hi All,is it possible to setup 7961 IP phone with SSL VPN and IOS router as edge device in main site? we want to setup IP phone to register in CUCM for remote users without to configure site to site or server/client VPN? I know we can setup ASA with ...
Someone in our customer services group asked if I could have the ANI on outbound calls be the800 number for that group. Is that even possible with CUCM 7? Would the SIP PSTN provider like even allow that?Is it advisable? Common? Thank you.
I'm configuring H.323 voice gbateway for our branch in UK, appreciate if someone can share the UK dial plan. local, national, international ...etc.Regards,
Need help after i factory default with below method, then the ip phone show "Unprovisioned", then "File not found SCCP48" then reboot by itself. Running on SCCP, CUCM 7.0. Only this phone having problem while to register, all other phone running fine...
Hi,We have an audio codec problem in our calls involving our telephony system and our providers Cisco AS5300 trunk.Our telephony system is Asterisk version 1.6.2.14 . G729a Codec is licensed, bought from Digium.AS5300 trunk is our outgoing calls sip ...
Hello FriendsI Made new Implementation of IPT with CUCM 8.0 (Pub and 1 Sub) and H323 Gateway. Calls are working fine, But When I make Conference call Internally It fails. Suppose from Phone A I called Phone B, Phone B Answer Call. From Phone A I pres...
Hi Community,I'm actually tryihg to configure a SPAN Destination Port which is also able to send and receive Traffic for the host itself. This feature should be possible with the "ingress" sub-command.Here 's a sniplet of my config:!interface Gigabit...
I have a client who has CISCO2911/K9 routers deployed around their branches. We want to deploy Cisco voice (CME) using the routers as edge devices and voice gateways. What componets do I have to add to the routers to achieve my goal. I understand the...
Hi,We have a SRST GW(2911) in one of our remote branch where PSTN analog lines are terminated locally to the GW and the IP phones are registered to Head Office. Need to setup Auto attendant or IVR in the location. How to enable CUE in the SRST router...
