Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I'm upgrading my CME to 4.2 version and the process is 99%, is it normal ?for me not !CCME-EP-AUSTRALIA#sh proc cpu sortedCPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 93% PID Runtime(ms) Invoked uSecs 5Sec 1Min ...
Hello,The Cisco Call manager is version 4.2 using a private network of IP addresses.Regular IP phone calls are working well in every direction. The problem that I'm experiencing, is when two people, connected via Cisco VPN and using the Cisco IP Comm...
Do I need to upload a firmware for 7941g phones into cucm 5.13 or is the default firmware good to go?Thanks
Hi Guys, I have the following doubt:When I work G.729 for call external its use 24K for call, When I work G.711 for call locally its use 80K for call. Ask, If I will have 03 sites for example(Sao Paulo, Rio de Janeiro, Minas Gerais), if I work in Sao...
We have Emergency responder version 1.2(3a) sr2a and I need to import a switchport details file. When I am exporting the switchport details file I don't see anything in the location column.For the other column everything is OK. Do I have to rewrite a...
Hi,How to enable the caller id? When a call arrives from outside via PRI lines to call manager express the users do not see caller ids. How to enable it ?thx
I'm not able to register this SIP Phone to the CCM5.0. I have device license that cater all IP Phone models.(LIC-CM-DL-100=)I got error message " Login Forbidden" "timeout" in the IP Phone.In the CCM, I got this message in Phone COnfig Window Registr...
Hello I have a problem integrating the CUCM 6 with an Active Directory. I configure all the parameters of the LDAP system and the LDAP directory, click in the sync button, and the system tell me that the proccess is succesfull. I have end users that ...
I have 2x 1Mbps PPP links from my core router (3660 running OSPF) to one branch (02x 1841) that need to be balanced. My concern is about the load at the branch's routers (02x 1841), if I enable OSPF, considering that we don't summarize routes and my ...
We are in the process of moving to CCM and Unity and currently have an Avaya G3 and Intuity Audix in place. We would like to migrage users to CallManager with Audix in place...we have the G3 and CallManager linked and call call from one system to an...
Hi, i need you help. I can't to make a backup. The follow message appear:ERROR: Error, unable to move tar file to: /common/drf/2007-11-12-14-25-28/2007-11-12-14-25-28_SUB-LAFARGECH_CCM_LOCALE.tar,Pls.see the attachments.Any idea?
Hello,Voice termination applies to a call that has two call legs, one leg on a time-division multiplexing (TDM)interface and the second leg on a Voice over IP (VoIP) connection. This termination function isperformed by digital signal processor (DSP) ...
Hi all.We have two CCM (1 publisher and 1 subscriber).Now all phones register on publisher.We want to make some "load balancing" and register some phones on subscriber.We have made a new VLAN, a new dhcp scope, and in this scope we have configured su...
We have about 350-400 7961G IP phones in our network and since about a week quite some (I think at least 10 reports/day) calls don't have inbound sound: The external party does hear us, we don't hear them. This problem happens with both inbound and o...
Hi,i have a GSM adapter plugged into a fxs port.If i place a call from a IP phone everything works fine. If i put on hook the ip phone and try to place another call i get a busy tone and the only way is to unplugs and plugs again the cable that conne...
