Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, I was doing research about cucm phone, directory services. I am confused with the different configuration pages and could not find relation among them. I did not know which part exactly is doing what.From this perspective could you please explain...
Hi Guys, Emergency number continuous ringing but no answer.Please find the attached logs. IPphone--> cucm --> Sip Gw --> Pstn Calling 04-4361015Called 999
Hi,Usually I use calling party transform mask on route pattern , Is there a way to use on sip trunk instead of calling party tansform mask on route pattern Thanks
So I understand that an eToken is requried in order to do any security in Cisco UCM (phones, voice ports). Is there any alternatives without using eTokens?If the eTokens are required do we HAVE to use the Cisco USB eTokens (i believe the part number...
I have a problem when I try to do a restore in a new CUCMI registered my backup device and my CUCM saved it succesfully, but when I try to make my restore wizard my CUCM can´t find the restore file that I saved.When I try with another CUCM I have no ...
Hi, I have received BE6K received from cisco pre loaded with Unity connection. After completing the installation of CUC.I reloaded the CUC. I observed a CUC VM has not VMware tools. I was unable to access the CUC via CLI/Console/GUI.for reference scr...
Hi, I would like to know if anyone have been experiencing some freezing issues with 88XX phones? We first received the phones with the firwamre sip88xx.10-2-1-16 but since the phone was looping through reboots when connected to 2x or 3x 8800 modules...
Hi, I have couple of CISCO AS5400 and would like to set up MGCP to communicate with Third party Media Gateway controller.The objective is to use the CISCO AS5400 to just process the RTP via SIP. there is no E1/T1 Interface. I have looked at many setu...
Hiwe have CUCM 11.5 and UCCX 11.6 and recently added new CUBE in our topology. Some of our incoming calls confront with DTMF problem. We have set DTMF command under our dial peer configuration, but still we have problem.We have 2 SIP Trunks that one ...
Hi Team, Please let me know is there an update to do Call recording for Cisco ATA 190 & 191, when it is connected to CUCM and CME.1. How to do Call recording if Cisco ATA is connected to CUCM ?2. How to do Call recording if Cisco ATA is connected to ...
Hi allI have a cisco 2811 router with pvdm2-32 and vwic2- 4FX0 and IOS version of Router is 15.01 when I use this router as a fxo gateway : in outgoing calls , the Co line is occupying but no connection to called number is happening , just some ...
Greetings - As part of an in-progress CUCM 12.5 setup, I've setup and run LDAP synchronization with our AD.I'd like to know how I can undo the LDAP synch and start over from scratch. I believe I can delete the existing search bases (I'm using eight),...
Good morning - We just recently started receiving this error a couple of days ago. Nothing in the environment changed, but the directory simply stopped working. What is even more odd is that my phone (8865) could browse the directory yesterday but it...
Dears,i have a below UCS M3 server BOQ in which it has E5-2643 CPU running 11.5 version of CUCM,, hence the supported hardware link only shows M5 hardware, this server was purchased for 9.1 and it has been upgraded to 11.5 since from past 1 year i d...
When creating a new phone in CUCM 11.5, I would like the line setting for Forwarded Call Information Display on Device to automatically be set to Caller Name and Dialed Number. Does anyone know where this setting can be done so it will apply to any...
| User | Count |
|---|---|
| 8 | |
| 4 | |
| 3 | |
| 1 | |
| 1 |
