Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
About once every minute a new entry is created, which fills up the Voicemail mail (10,000+ entries!)From: Cisco Unity Connection MessagingSubject: Message from Unknown sender (Unknown caller ID)Duration: about 19 secsMessage: If you want to turn off ...
Hi,It seems like that CTL and ITL hash of the newer series phone types (7800/6900/8900) is different the the good old 7900 series.When comparing CUCM CTL and ITL to a 7900 phone they appear the same, but different from the mentioned phone types.Anyon...
hello dear friends I have a 2811 and a 2821 I have e1 module on them and use the e1 ..it's work very amazing ... I want to monitor the E1 connectiviy from PSTN . if E1 is not working from pstn ( it's happend sometimes) alert me or creating a log......
We are planning for our old setup of CUCM 8.0 version (1 pub & 2 Sub) to version 11.5 ..is there any challenge with IP Phone CTL files installed from old cluster...is there any precaution do i need to take before migration related with IP Phones ... ...
Hi, Can we configure hotline lines with hunt groups in CUCM? BRAbdul Karim
Hi,We are running CME 8.6. We have nearly 100 SCCP Phones and 5 SIP (9971) Phones on this CME. The SIP Phones are being projected as the 'top of the line' model and should be better then there counterparts..right?? But we cannot see the local directo...
Hi, I am trying to find a solution to problem where if I call to 8851 phone internally I cant see the caller ID. Can someone explain me the difference in configuration on CME for 8851 phones and 7945 phones? I cant find any helpfull links. Please Adv...
Hi all i have registered Avaya 9611 & 9641 IP phone to CUCM 11.5 below is the issue summary. whenever avaya phone tries to reach Cisco IP phone on same call manager it able to make outbound call however when Cisco phone try to reach same avaya phon...
Hi,Yesterday I configured my third party sip phone which is yealink in this case on cucm and successfully registered it with cucm, despite of registration i have some calling issue in this phone. I am able to make outbound calls from this phone to an...
Hello,I have a minor issue with Sip phone configured in CME. Phone is getting registred but name is not getting updated. if there is any fix for this issue, please advise. Phone Model : 7841 ===============================CME config: voice registe...
Dear Team , kindly help me regarding my below issue and informations. we are deploying Cisco phones and currently Avaya phones are using it. the concern is existing Avaya system working with 802.1x authentication and same way i have to deploye in Cis...
Hello, Is it possible to specify certain channels to be used, or others not used, on the 8821 admin web page? I have been looking through the 8821 Admin and Deployment Guides but unable to find anything. This was possible with the 7925 wireless hand...
Hi,I have a problem that when SRTP mode is enabled on SPA 303 and 504G answer "488 not acceptable here" on incoming INVITE. SDP of incoming INVITE:v=0o=FreeSWITCH 1505106066 1505106067 IN IP4 38.108.164.66s=FreeSWITCHc=IN IP4 38.108.164.66t=0 0m=audi...
I can not wear a headset on my head. I need a wireless or bluetooth headset that can sit on my neck with earbuds to my ears ( much like workout headphones that connect to your cell phone). I have a Cisco IP 7965 and I am in search of an adapter that ...
Hello All- I've read that the 3905 should be supported on CME 8.8 and greater. I have a system running 9.1 and when I run "load ?" I don't have the option for a 3905.... Am I missing something here? XXXXXXXX-CME#sh telephony-serviceCONFIG (Version=...
