Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear Cisco Team and All, I am confused because each telephone line is working fine on single direct telephone.but i am installing 4-Four lines on VIC card but unfortunately its not working, so after that all line is not working...i am getting ring...
I just implement CMC code to restrict users being making calls without enter the CMC code. But I faced problem that when the users prompted to enter the code or password, the code appears so anybody can see it. Does anybody know how to make that ...
Hi Guys, I have a 2811 ISR router. I want to configure MGCP PSTN gateway on FXO port. here i am mentioning the ios details: Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2) is this fine for m...
We have Cisco Catalyst 6500 Series Switch with CMM Module and Supervisor Engine 32, infra team will replace the SUP 32 with new one 720 with new IOS will this affect the CMM function , i know the CMM is compatible with SUP 720 but what about new IOS ...
According to the CME Features Roadmap, the night service bell is now supported on SIP phones. The documentation on the Cisco website would have you believe that it is possible to create a Night Service button on SIP phones, there are at least two ref...
Some users are complain that some time they faced a silent call (each party cannot hear anything) so they close the line and call again to make the call work. But this issue occur suddenly so I can't capture the packet or do anything to fix the issu...
Hi Expert, We are facing problem of hearing calls from some branch offices IP phones (model 7921). After established a call this problem is happening. We could not hearing the branch office as well as they could not hear us. What are the reasons and...
I have a number of Cisco 7906 handsets configured with Tel2 SIP provider. Everything works well 90% of the time but occasionally traffic seems to get blocked and we have to switch to using port 50600 instead of port 5060. I am using SEPXXXXXXXXXXXX.c...
Hi guys, I have a customer running CUCM 8.5.1 on old MCS hardware. I want to use PCD to move them to virtual using the same IPs. However, I am a little concerned about the target version. Does it make sense to go to 11.5 directly? If so, how do I...
Hi everyone, I am planning to replace all certificates on UC servers that are signed with SHA-1 with certificates from our internal CA. I want to make sure I don't run into any issues with our ITL files for the phones such that I have to delete the...
Hi, Could someone please confirm if the Cisco 1921 supports VoIP? From what i can tell the Cisco 1921 router does not support VoIP, even with a VWIC3 card installed. This diagram (from http://www.cisco.com/c/en/us/products/collateral/routers/2800-s...
Hi All, I have an analog gateway connect to analog line to call to other country. The pattern is: When user dial "123", user can hear tone (This is the tone connect to the gateway) Then user dial "2" mean connect to country A. Then user dial "567" f...
Hi, I have a client who wants " Please set hold beep notification to every 90 seconds, it currently beeps every 10 seconds when anyone is on hold." Where changes are to be made? System version: 8.5.1.13900-5 Please advise, how can this be done? An...
Hi All, Guys i am in trouble, I have configured cisco router 3825 as a CME version 4, all the calls including inbound and outbound were working fine, suddenly issue raised that all the outgoing calls are not making and incoming also, i have check ev...
Hi All, May I know if how to performed a bulk speed dial for user device profile (Extension mobility). I just need to update almost 3000 device profile for speed dial. I am not sure how to do it. Thank you so much
