Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, I have a strange issue with sip normalization scrip. Customer want to change diversion header using with sip normalization script but same time they want to use refer-passthrou scrip on sip trunk . Is that possible to use following script sing...
Hello All, I am completely newbie for this field, please forgive if there were any mistakes from my side... I am trying to configure calls between two SIP accounts that is between VICI and MATRIX PBX, but receiving an error stating below. --[Jun 2...
Hi All, We have a situation were in the UCCX engine status on Primary server changes to Master and secondary becomes slave. Again secondary becomes Master and Primary becomes slave and we have keep updating the URL in the phone services. Is there a...
I bought a a Voice-enabled Cisco 2821 ISR Router for my Cisco CCNA Voice Collaboration LAB loaded with Cisco Unified CUCME/CME 8.6 (Call Manager Express) and CCP 2.7.IOS version is Mainline 15.1.4.M10 Adv. Enterprise Services (c2800nm-adventerprisek9...
All,When a 7960 send a tftp request to a TFTP server to load SCCP image, the phone sends a "malformed Packet" in the tftp packet. Currently the 7960 runs a SIP fimware. Any idea why?phone(4.4.4.6)---------------TFTP-server(4.4.4.8)Here is are the fi...
I have a client with existing fax numbers on PRI. The PRI terminates on a Cisco router and sends the incoming faxes to an eFAX software using H323. I want to forward calls for a specific number to another external number. For example, the existing ...
Hi guys We have a new setup of SP > CUBE > CM. Outbound calling works fine, audio both ways. External callers inbound get dead air when they dial in, no ring back, although the phone does ring and can be answered. The phone itself is showing no recv...
Hi all, I have a customer with a CME 10.5 and only SIP phones.I have never installed TAPI on CME, but does this work with Cisco SIP phones?The models are 88XX and 78XX Thanks JH
Dear All, As I understand phones that are in SRST mode will have the same DN information that they had from CUCM, but how about IP address information, does it change?? how will they get?? Thank you
Hello All, I am completely newbie for this field, please forgive if there were any mistakes from my side... I am trying to configure calls between two SIP accounts that is between VICI and MATRIX PBX, but receiving an error stating below. --[Jun 2...
Hi, we recently upgraded our cucm 6.0 to version 11.0. in a isolated set up. The upgrade path was: CUCM 6.1.4.1212-1 --> CUCM 8.6.2.21900-5 --> CUCM 11.0.1.20000-2After the upgrade none one the phones are able to register with the CUCM. All phones ar...
Hi,is there a way to save the user/password during VPN authentication process?We are running CUCM 9.1.2 + ASA for register 2 IP Phone. The problem is that when the phones got unregister because some electrical or internet issue at the remote site so...
Hi guys, I have this scenario: I have two cubes working in HA and they will have the HSRP configuration according to the guide "Cisco Unified Border Element High Availability (HA) Using HSRP", in order to send the calls to the remote PBX I will confi...
Reciban un cordial saludo desde caracas,venezuela. Realizo una consulta a este foro y es acerca de la posibilidad de poder realizar transferencia de llamadas y conferencias cuando se establece un trunk intercluster entre 2 call manager ...
