Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Running CME on 3825 router, with several SCCP VoIP phones up and running fine. Also has Unity Express VM, working fine. Now I'm trying to add a SIP phone. The phone has aquired an IP address from DHCP, and has TFTP server location and CM IP addres...
Hi guys, I did integration with tiger for cdr and extensions, CDR is OK but tiger couldn't be able to see my CUCM extensions! I did AXL services and configuration I already showed the extension in Attendant console with AXL so my AXL is working! wha...
Hi all, When I call an IP Phone from outside of my cell, and I finished the call from the IP Phone, my mobile remains in communication, i mean busy. what is the probleme here? so what is the configuration i should includ here? Thanks in advancce
Hello, VG224 is not supported with CUCM 11.X? http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/uc_system/unified/communications/system/versions/IPTMtrix.html#pgfId-1163273A At the matrix of compatibility does not show the recommended IOS Version. R...
I will migrate a cluster of two MCS Servers running CUCM 8.6.2 to CUCM BE6000 10X. I have some questions: 1 - What´s the better way to accomplish this? Using PCD or install version 8.6.2 at UCS and upgrade to 10X? Or i install the CUCM 10.x and uses ...
Hi, We have experienced registeration problem in SRST mode for IP phones that have sip firmware. Sccp ones registered properley. I can monitor sccp phones with "debug ephone" command when they register or unregister, But Sip phones dont even try to...
Dear All, Actually, I wanted to make a factory setup of a used Cisco 7942G IP phone. The setup standard procedure works (blinking lights and pressing 1234 .. # buttons) until the upgrade menu appears, but unfortunately not completes the upgrading pro...
Hi all, Is there any tool out there that can be used to query an IP phone's network configuration. I need to know if multiple IP phones have DNS IP configured. Thanks
Hi Team, Cisco IP Phone 7937G is stuck at "Configuring CM List. Before making chaages on network end, this phone was working fine. To check network setting, We have switched over this phone to another working phone LAN cable, there also getting same ...
Hello! I have some problems with SIP Trunk when I call to local city numbers from cisco 3905 7821 sip phones. I attached sip debug. Please help me!
Hello, I have a lab with UCM 10 and a SIP gateway connected to a PSTN cloud via a PRI (CME routeur, translation rules, 7962 and so on) When a PSTN phone makes a call to the MVA DN, I ear the greetings and I am prompter to enter my PIN Code. The syste...
Hello, Good day! Would like to ask regarding this issue. When someone called the Hunt Pilot and one of the extensions answered the call (ext. 305) then transferred it to another extension internally, we can't hear anything then the call got dropped. ...
We deployed a ASR1001 as a SBC to connect to PSTN, our SBC takes the inbound call from SIP provider via Trunk-A and transfer the call to an audio bridge via Trunk-B. But, our SIP provider will send the SIP signal with Min-SE=90, we must setup the Min...
Good day Would it be possible to set up the Directors phone so that for external calls (cell phones and other non internal calls) only they come through the secretary first but all Internal calls can be phoned directly to the Directors phone. I'm usi...
We are having site A where BRI port installed on Voice gateway & some BRI lines a configured on it...... Can we use free numbers from Site A to the New Site B ...i mean can we use BRI channels installed on location to the other location ..
