Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I'm setting up a new branch office with CUCM and Unity connection in HQ and h323 GW in branch office. The phones are registered with HQ CUCM and everything works fine. The issue is with Unity Connection. I followed exactly how other remote site is...
we have a ATA187 that has one port connected to a Viking FXI-1 paging interface. when a person calls the extension the paging works but we get a fast busy after the user hangs up the phone. this fast busy persists until the timeout occurs on the Viki...
I'm having an issue with the CME of one of our clients. At their main location they have a number of 7961 phones, as well as a single 7975, that are not receiving the call waiting beep. I have checked the configuration and confirmed that this setti...
Hi all,After a recent upgrade from CUCM 8.6 to 10.5, two 7941G phones failed to upgrade their firmware to device default (SCCP41.9-3-1SR4-1S). It was discovered that the 2 phones in question currently have SCCP41.8-3-1S firmware loaded on them, whi...
Hello, Unable to register Cisco soft phone as SIP. it keep saying "Registering" but number is reflecting on screen. CUCM version : 10CCP is showing as : SIP, when checking model information. Thanks,Deepak
CUCM: x1001 >>FWD>> x1002Although calls go to x1002, voicemail messages still end up in x1001's mailbox.What features are available in CUC to enable x1002 to collect x1001 voicemail messages (deliever to phone not email)An attempt to get this working...
Hl team,I only wanted to know how much bandwidth a single IP phone takes to register over wan?if there is a failure all my phones will register to a subscriber which is at remote office and mpls connectivity.I know 90 seconds is time frame for regist...
Hi and thanks for your help!I would like to know if this is possible to listen to a talk between a customer and a employe directly from a phone that is own by a supervisor? I have seen this:http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/uc_system...
Hii have just configured a voice gateway (2900 series ) to make external call via FXO portswhen i started the configuration i faced a problem : the voice ports are not displayed and the voice commands couldn't be executed (the lisence of Uc are not a...
Hello, I'm running into a problem. Could someone please give some hints.I'm running CUCM 6.1.3.3000-1 on a MCS7825I3. Whenever I run a query with two filters on CUCM Administration webpage, I get this error:"Error occurred during find. javasql.SQLExc...
Dear Supportforums's Members,We have a customer who is running on Cisco Callmanager 6.1 and this product is end of support so cant take help from TAC :-( Could someone can help me here to resolve the dbreplication issue. Below are CUCM nodes in clust...
Please find the attached traces from our gateway and STC side. STC is saying PBX problem Can anybody from Saudi test this by dialing 8007490000 from their SIP trunk .
Hi everybody,In a CUCM cluster, 1 PUB and 1 SUBif the Publisher is down, does the subscriber will store the CDR in database?Because it seems there is no CDR service can be selected in SubscriberAny Cisco official document does mention about that?Than...
Hello All,I have a situation where I need to get a remote site setup with a few IP phones and I have never done anything like this.I have them setup on our DMVPN with a Cisco 2821 and a default route out to the internet. Remote office is currently us...
Hi There,I'm trying to configure a 7940 as a SIP Client using Vbuzzer SP.SIP Provider (69.172.204.134) <-----> (99.225.192.171) NAT Router (192.168.0.1) <------> (192.168.0.12) 7940When I use firmware P0S3-8-2-00, I can get inbound calls, but outboun...
