Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I have a AS5350 with E1 2 PRI DFC on it. E1 line is terminated on the cisco AS5350 and then there is a trunk between this and an Asterisk server. The setup works fine and all incoming calls are forwarded to asterisk server and properly handled. Pr...
Hi,We have a lot of CP-7912G phones with SIP firmware and were used with Asterisk before. Now we have procured new CUCM 9.1 and trying to revert back those phones to SCCP. Looking at various other pages of this forum, we have found a way to prepare g...
Hi, I'm looking to implement CME 9.1 on Cisco 2951 at new office.Since there's Toshiba VoIP system in place at old office, we are migrating the whole ISDN channels to the new office and looking to set up a SIP trunk via P2P WAN link and route the cal...
HiWe notice in our cluster that, some 8945 sccp phones do not give MWI (LED as well as on screen) and also 9971 do not give MWI.Voicemail comes from cisco unity connection..And phones are registered on CUCM.Some 8945 even show DND key status when pre...
Hi,I'm planning to upgrade the MeetingPlace to CWMS. I'm afraid some user behavior of MeetingPlace is missing on CWMS, e.g. create the meeting by phone through CWMS, define the meeting ID from CWMS.Any one upgraded the MeetingPlace to CWMS? Any compl...
Hello All I have a CME 8.6 router with one PUBLIC IP to eth0 interface. Do you need to do NAT for all IP phone to make and receive calls ? Currently I have configured NAT and I did not BIND media to any interface . I could able to make calls but Audi...
Hi All, I'm planning to upgrade CUCM 8.6 to 10.5. We currently have 7500 OVAs using 2 x 80GB vdisks. The requirments for 10.5 says that we need to expand the disks to 110GB.I have read the pre upgrade tasks on how to do this by installing the ciscocm...
Hi All, We have a call manager 6.X cluster with remote sites. One of the remote locations is experiencing the low bandwidth error message. This message occurs sometimes throughout the peak times when no one is using the IP Phones. The WAN link is usu...
Hi - I was troubleshooting an issue out of hours and the voice gateway I was working on crashed after using a debug commandWhats the best way to recover the gateway?I'm unable to ping it now - do I need someone to reboot it?Once it comes back up with...
Hi -I'm trying to make the length of a wav ring tone continuous. without any pause. How would I do that its for a panic button solution.
Ahead of our upgrade to CUCM 10.5, I'm trying to push the firmware to our phones to minimize issues during the cluster upgrade. I've been able to push the firmware to our fleet of 9971s with no issue. But, when I try to push the firmware to the 794...
I'm creating my UDT's for a 10.5 deployment. I want the description to be #FirstName# #LastName# #TelephoneNumber# on telephone number doesn't seem to be a valid entry. I have also tried telephone Telephone telephoneNumber DirectoryNumber DN all t...
Hello,Is there a way to stream music to your ip phone speaker ?
Is there a way to disable the Divert option on 8945 and 7841 phones?
Hi dears,i am facing issue related to Call forward all- We have SIP (283XXXX) and E1 trunk (494XXXX)- I am trying CFA on cisco 7911 and providing mobile as destination.- I am using user profile to login on the phone for SIP and E1 DIDs- For SIP when ...
