Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,I'm often using IP Phone web interface to debug connectivity problems.In the Network Statistics -> Network page, I suppose we see the real speed the ports are running, and the refresh is immediate upon change.But what are the informations displ...
HiWe have a setup on one location that looks like this:Ascom phones -> Ascom CallManager -> WAN -> CUCM 8.6 -> PSTNEverything seams to be working ok but transfering calls from the Ascom phones then it fails.When pressing the R-dial in the phone a new...
Hi All UC experts,I want to change the hostname of my CUCM 9.1(1), but this is running lots of services already.According the Cisco guide, the steps are very straightforward: http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/install/9_1_1/ipchange/i...
VG 2XX Data sheet says:Cisco IOS Software-Based Hardware: The hardware includes uniform Cisco command-line interface(CLI) and Simple Network Management Protocol version 3 (SNMPv3) support for ease of gatewayconfiguration and operation.Do VG Support's...
Hello Experts,Our customer needs additional 18 units of 7945G for CUCM9.1. Can we use LIC-CM-DL-100= for this additional license? Thanks a lot.Best regards,Zin
Dear my friend.I have configured E1 R2 line for my customer.It's use to receive and make call from/to PSTN. But my customers said that their call sometimes had been dropped suddenly and sometimes they can't hear from far site.Please help me to verify...
Hi,My customer have a plan to move their PSTN line form Siemen PBX to Cisco Router 2911 (VWIC3-2MFT-T1/E1).They said that they're using E1 R2 but the signaling has 2 directions, for incoming call from PSTN they used E1 R2 MFC signaling,for outgoing c...
Hello,I have rejected MGCP endpoint registration. (Status Column in the CCM 5.0 : REJECTED)What could be the possible causes?best regards,
Hi guys,Recently, my company wants to do VPN from branch office to HQ. The CUCM is located in HQ where my IP Phone is located in branch. Our branch office are currently using ASA 5540 firewall running context. Can anybody guide me on how to perform V...
If we have CUCM-HA ( PUB/SUB )Unity Connection-HA ( PUB/SUB )The unity connection is UP but the Telephony Integrations is not in place yet.To configure the Connection HA........- Do we need one "phone System" - with 2 diferent AXL serveurs ( CUCM...
Hi,I have setup a sip to sip CUBE.The calls are pushed from CUCM to the CUBE via a sip trunk.This works ok.Calls coming from the SIP provider into the CUBE and on tothe call manager are not working.I can see the calls coming into the CUBE.I can test ...
Hello !I would like to use my 2811 router as a CUCM voice gateway (MGCP), What module would I need to get as a minimum ?Does a VWIC2-1MFT-T1/E1 work ? - as per the Cisco web site, it should, but do I need to add DSPto the router to make the voice wo...
Dear Folks, I am restricting few conf phones with Client Matter Codes... Why is the CMC is not consistent... With all the configs done... Route patter --> Client Matter Codes and the relevant CSS.... It works for the first time and stops working for ...
I have a CUCMv8.0 and a Gateway 2901, this Router is configured as H.323 Gateway and it has 4 analog lines connected in the fxo ports. The calls received in the fxo ports are transfered to a Cisco phone 7942, the call is process correctly, but when I...
I have 10 users with 7960's in a remote office. the phone stations hang off my main call manager in the central office. At least 70% of the time a remote user attempts to make an outside call they recieved the alternate dial tone after pressing the...
