Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi Guys, I have a question for you, we are thinking of disabling Media Inactivity call detection on our voice gateways I was wondering if you knew what impact this could have on service? Having a look at the following article about setting it up and ...
Hi all,we plan to upgrade a CUCM cluster Version 7.1.5 to 8.5 or 8.6 with transfer the CUCM to VMWare.We have the following HWHWCPUMemoryHDPUB 7835H2Xeon 2,33 GHz 272Sub 17845H2Xeon 2,33 GHz 4136Sub 27835H2Xeon 2,33 GHz 272Sub 37835H2Xeon 2,33 ...
Scenario:(using CUCM 8.6.2.21900-5 for phone and Unity for voicemail)If someone calls phone_A and phone_A does not answer, the call is fordwarde to phone_B (cell phone) using "Remote Destination Profile Configuration / Remote Destination Configurati...
I am opening this discussion because a confusion regarding a part number MCS7845I2-K9-CMC1 and its hardware support.Customer has a Cluster of 4 CManagers and all of them were Apliances MCS7845I2-K9-CMC1. We are trying to determine its CORRECT EOL for...
Hello,I have a CUCM 9.0 and I try to use Mobile Connect.My CallManager is in UK, and when I call an internal number (6017), I want to ring too a French mobile (so 90033xxxxxxxxxx#).I've created remote destination for this number as...
Hi,Is there a way to see the conference list on 6921 and 6941 IP phone and remove the participants from the conference?Regards,Pawan Arora
Hi everyone,I'm working on Unity Connection 8.5. I need to use the Bulk Administration Tool to enable SMTP Notification Device to email users when they have a new voicemail message. There are 3000 users that need this update - I'm wondering inste...
Lab setup, not production. Exploring to learn.Setup: Analog phone -> PBX Emulator (Cisco 2811)PBX Emulator -> Near Side CME (tie line between them is FXS <-> FXO)Near Side CME -> Far Side CME via a SIP trunk2 x SCCP IP phones off Far Side CME.Sit...
Running CUCM 8.6 with various SIP trunks, specifically I have one integrated with MSFT Lync. The available tools I have are RTMT and the out of box reporting and CAR (CDR). I want to determine how many calls have been placed over that trunk. I know I...
Hi All, Having an issue with abbreviated dialing where I have a user getting a "number not configured" message. It works fine on my phone and other phones in the office that I've checked or have configured. He entered his numbers through the speed di...
Dear All,I have ordered upgrade kit for CCM 9 through PUT tool. I choose e-delivery option. I receive the upgrade confirmation from cisco.When I start to download the medi kit, it asks me for "K9 form". Did any one know what is this ?thanks in advanc...
Hey team, I have a environment working properly between 2 UCS with CUCM 8.6. In the same voice network I have a integration with analog central, so I have problems in the call identification when the call comes from a analog phone. So, The managers w...
Hello,I am trying to setup a new sip trunk (new connection) to ITSP, whenever i dial a PSTN number i get a fast busy tone, My ITSP says everything is OK from their end,Can anybody refer me for step by step troubleshooting docs for such type of issue....
Hi I have Cisco VGW (Cisco 2811) which having a SIP trunk, i need to change the "from" value of the calls which going through from particular dialpeer, The reason for this when i used "Calling Party Transform Mask" in Route pattern, when internal ext...
Hiwe recently configured sip line from our itsp on branch router cisco 2811,there was a problem in outbound calls dtmf while the calls were originating from cisco 6921 phone, i checked mtp required option on sip trunk on cucm 8.6 and the issue got so...
