Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have recently done a new installation wtih 8945 and it was my first experience with these phones and what surprised me is that some of the functionalities that I had with 79xx series are not there anymore. For example I cannot get the join softkey ...
Hello, I am running Cisco Unified Enterprise Attendant Console 8.0.0.5. On the attendant console user pc's the status icons are blank for some phones and on some it works. I have restarted the AC service on both Publish...
I have two clusters, one with CUCM v7.0 and one with CUCM v8.5. We have an inter-cluster trunk setup between the two and are migrating users from the old system to the new one. Calls can be made between clusters just fine. I need a way to seemlessly ...
Hi,if someone leave a message in Unity Connection and the recipient is hearing the message by the phone is there a chance to dial direct the number of the original sender who leaves the message?
Hey Guys,Trying to add a h323 gateway on CUCM but it doesnt register. below is the gateway configuration. What am i missing ?card type e1 0 0logging buffered 51200 warnings!no aaa new-modelclock timezone INDIA 5 30network-clock-participate wic 0 netw...
- i have a gsm gateway connected to my CME router , so i configure all incomming call from outside to 4 SIM on my gsm gateway forwarded to my Auto attend number also my FXO port .so , the problem when a call join my AA customized from the gsm gate...
Hi,just now i'am in the implemantation of a new cucm cluster for one of my customers. I have 4 CUCM's in the Cluster,and a centralized SIP Trunk with 2 Cube's ( 2 x 3925 ) in active/active mode. Every Cube should handle a maximum of 500 concurrent c...
We're needing to upgrade our customers server so it has the latest windows patches. The server is currently running Cisco OS 2003.1.5aSR10 and UCCX 7.0(1)SR05. We've been advised to get certain critical windows patches applied, but can see in the Cis...
We have two clusters, one for all phones and the other is for an automated phone system.We have a route pattern that is a four digit number and is pointed to an ICT trunk.The ICT trunk connects CUCM to a prompt in Contact Center Express.When a phone...
Hi to all,I added a new subscriber server in my cluster and I change my CM group in order to have my phones registered at this new subscriber but they are not.In the cluster i have this "site A PUB - SUB (the new one) and site B SUB", I can change th...
Hello,I ran into a new one today. I have a situation where we have two users, each with a 9971 (one is connected to the WLAN if that matters). UserA dials userB and video is established, works fine. However when UserA then hits the conference button ...
Hello,We have a CME , lets consider we are making internal calls:when user A is speaking on the line and user B calls user A, is there a way for user B to get that user A is busy or on another call without limiting user A to a busy-trigger-per-button...
After updating IOS on a UC520, I noticed that outbound calls via SIP Trunk (voip.ms), stopped working. Whenever I would make a call outside the network, I just got an operator message saying, "That number has not yet been assigned." I thought this me...
Hi, I am using Cisco 7940 Series IP phone with having account 8x8(8x8.com).I try to configure it.I able to make a outbound call,but not the inbound call.I try to disable NAT and put 8x8.Please help me out
problems with CUPC conversation windowthe conversation windows does not close after disconnectswwhen happens user cannot make nor receive callsCUPC version 7.1.2.13964 (for MAC)MAC OS X Version 10.8.3
