Resolved! Group Call Pickup
Hi,2 No's group call-pickup, pickup each other calls though they are not associated to each other groups, why ???? Thanks
Hi,2 No's group call-pickup, pickup each other calls though they are not associated to each other groups, why ???? Thanks
We have a very minute problem with our phone system. Not entirely sure if it's how the software works or it's because it wasn't programmed correctly. But when one of our phones tries to transfer a phone number to another number here it displays a dif...
Good morning,I've a cucm 86.2 configured with one device pool with alla user and two css: lugano and hong kong.The lugano's usera can be call alla numbers and the hongkong users can be call only the lugano's users.I've created two css that contain th...
Hi I installed a new UC500 last week. Incoming and Outbound calls disconnect between 40-60 seconds after answering.I attached the Debug ccsip all. can you let me know the problem CME 8.6IOS : uc500-advipservicesk9-mz.151-4.M4bPhones 7942 PSTN -->> SI...
Hello All!On the two servers I have clear installation of Cisco OS 2000.4.6 SR9. I have installed Cisco CallManager 4.1(3) Publisher + Subscriber, updated it to SR8a. Registered two test 7940 phones on it.The problem: RisDC.exe consumes a lot of RAM ...
I've been getting to grips with the BACD on BACD. I have a SIP trunk to an ITSP. I have specified to use the g.729 codec for various reasons. I find that BACD works, but I never hear any prompts - just silence. When I set the codec on the SIP trunk t...
firmware is 9.3.1.3, no missed calls at all 6921, cmeanother phone with firmware 9.1.1.0 shows all missed calls
Hi,I have two CUCM V8.6 communicating via a trunk SIP. I have encryption enabled on each CUCM's network and I would llike to ensure an encrypted communication between the two platforms. Any thoughts on how to have aencrypted end to end communication?...
Hi I have intalled CCME 8.8, i need to implement call controlling in CME, to get IDD calls phone should request a PIN, for local pstn calls also phone should request a PIN, how can we do this in CME ?Regds$
I've two uc549 connected over an internet vpn between a H3232 trunk.The UC540A is in italy and have two ISDN BRI The extension are 10x, 11x and 12xThe UC540 Bis in switzerland and have also two isdn bri the extensions are 16x. The user (for...
Dear All,I have provision the 4 hard-disk(300 each disk space) in RAID-5 as VMware environment.Requirement: Using UCS 210m2 physical server As per below mention provision for CUCM 9.1 / Meetingplace / IM & Presence and ELM server.1> VMware 1: CUCM...
Hi, can not set this controller as a pri-group or ds0-group for CCS or CAS signaling.In controller, only channel-group is availableCME_ROUTER(config-controller)#? Controller configuration commands: cablelength Specify the cable length for a DS1 l...
I am facing an issue where pickup/group pickup doesnt work for external calls. But it works fine for internal calls.External calls via SIP (using CUBE).Ill appreciate if someone can help me please
Hi all,I'm implementing CUCM 8.6 and I have some doubts with the SIP strunk.As per my understanding, If I make a call from my ip phone through a sip trunk, the source ip that is used to communicate with the other end of the sip trunk is the ip addres...
Hi, we have registered a IP phone 9951 on a callmanager 9.0, it seems there is no sccp protocol for this model just sip, so the phone is indeed registered but I can't have video-calls just audio-calls, is there any special config on the CUCM we have ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-07-2025 02:45 AM | ||
02-04-2025 01:17 PM | ||
02-04-2025 06:55 AM | ||
02-04-2025 01:31 AM | ||
02-03-2025 03:57 AM |
User | Count |
---|---|
3 | |
3 | |
1 | |
1 | |
1 |