Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I have setup CISCO2921/K9 as SRST & voice gateway. There are few FXOs connected to PSTN.There is no Voice-Mail module, I am trying to setup Auto Attendant using TCL scripts.call from outside PSTN to local PSTN numbers (connected on Voice gateway F...
Hi,I just wanted to know there is any way to find out in Application user page that associated device has diassociated.so,there is any way to track how it has disassociated.Any help is highly appreciated.
Hi,I have installed and configured the Cisco CISCO2911/K9 (revision 1.0) with the image c2900-universalk9-mz.SPA.151-4.M1.bin. Link is E1. (30 channels are used.There is no issues when the call is placed with the LAN,means IP phone to IP phone (diali...
Hi,I have a route pattern 9.XXXXXXXXXX that points to a route-list.In the route-list, I have the following two route-groups pointing to the same CUBE: - RG #1 Predot - RG #2 Predot + Prefix 999 (used to do some OTG header manipulation in the CUBE)I d...
Hi,I have NM-CUE installed on 2921 router. CUE version says 8.6. I would like to login & configure the CUE module for the 1st time. If i do a session to the module it asks about username & password. I tried cisco, cisco but it's not working. Can some...
Hello,I'm trying to provide 2 numbers in a Call Manager using VOSS. The phones are registered, you can call each other but in break out calls doesn't work. I have checked in traces that the From header in SIP INVITE is compesed by Country Code + Site...
Hello,Currently i am facing issues with 9951 and 9971 IP phones. Now they are registered on CME version 8.8, but they can make outbound calls somethimes and sometimes they cannot. Secondly, for one dial-pattern i can make a call and for another dial-...
Hello there, I have call manager version 8.5.1.10000-16 (still in testing phase) and call manager version 6.1.3.1000-16 cluster, one publisher and two subscibers (live CCM). CCM ver8.5 has exactly the same configuration that CCM ver6.1 has.When I c...
Hi,I have a problem for receiving fax wich is connected to FXS port. I can make and received call but for fax something happen, the fax´sdisplay shows receiving and then stop, the calling received a busy message; also the port remains some seconds se...
Hi,I want to implement/distribute 1 DID (ISDN E1 PRI) between two Callmanager express systems. Lets suppose I have Direct Inward Dial on Central site CME but I want to utilize/distribute half of the DID numbers/pool on the remote CME over the WAN.How...
I am getting the below errors in database when I am trying to run DMA to migrate/upgrade Call Manager from 4.2 to 7.1 any ideas :[05:10:16 PM] Accessing database...[06:21:15 PM] modExportDatabase=Failure[06:21:15 PM] Failed to complete database proce...
hello Guys,i am developing an application in java that sends a text message to a 7940 phone. at the moment, i have developed a small instant message application for users on the network but i would like them to have the option of sending the text mes...
I have had several cisco technicians come out and look at my issue and have had no luck. We have a uc520 with the latest software on it. I have 2 of the POE ports on it attached to two ap521's. THe phones connect fine and data works great. When...
Got a strange issue here... Environment: CUCMBE 8.6(1) connected via a SIP trunk to a SP. Inbound and outbound calling working fine for audio. Inbound calls to one DN are directed into a CUC call handler. DTMF tones are not recognised by the CH (and ...
Hi,I have extn numbers 000-098 assigned to internal users. Requirement was: If anyone presses 0 in the IP phone it should ring the reception number is which is 099. I created num-exp 0 099-it is working. The only problem is: after this command i am u...
