Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
A new lab setup2821 router with 2 E1 ports and a back-to-back E1 connected between them - on the same routerBoth ports Up & Multiple_Frames_Established. Well the Call is Ringing & getting connected - I just do not understand how and why is the debug ...
Hello,I am having trouble with 8961 phone. There seem to be delay specifically with consult transfer. Here is the scarnio -1. Party A calls.2. I answer the call.3. Party A asks for Party B's voicemail, extension 1000.4. I perform a consult transfer...
Does anyone have Visio icons/stencils for 9951/9971 and 7985 video phones? I can't find any on CCO.Thanks!Jeff
I have linked servers set up and I am able to successfully report off of the CVP Reporting servers. I would also like to be able to use a similar process to provide custom reporting from Call manager 7.1(3). Is it possible to set up a linked server...
I have an FXO card that will not forward calls. The outside phone line has been tested and is working and the FXO card has been changed. Once the call hits the port on the FXO card the calling party hears a ringtone, but no IP phones at the location ...
Is there no way to upload multiple files to the TFTP server in version 6? Have to add all my ringtones and background images to all 4 of my servers, ouch.
There is static on the phone, while the phone is still ringing. What I noticed after the call is established, the codec is G729. The call is to an external number, and it should be G711. Phones which uses G711, do not have any static. Is it becau...
I have a situation in one of my cluster , the publiser server is down with error on console" "NO INT 13h devices found" .I did reboot the server serveral times by removing drives, placing if firmly, running the support cd to upgrade the bios" but ...
Guys, i have the following topology:CUCM---[switch1]-------[switch2]-----IP phones | | SRST routerI have on both switches data vlans and voice vlans.Some of the phones at a random time failover to the srst router while the oth...
Hello,I have a Cisco UC540 on which are registred Cisco IP Phones. I configured a sip account to test SIP phones on UC, this is sip configuration :voice register global mode cme source-address 192.168.10.10 port 5060 max-dn 20 max-pool 20 authenticat...
Hi Team,I have a Cisco 7911G IP Phone and i want to install it on Cisco Call Manager Version 3.2.Please let know whether it will support or not.I have seen in the document that it supports only on Cisco CallManager version 3.3(5) SR1 or later. Let me...
The 9951 has 5 buttons on each side of the display. The left hand five I can configure using the normal phone button templates, so that's not a problem.But can I configure the five on the right hand side ? They seem to be change function depending on...
Good Day AllMy Publisher call manager is displaying an internal error when I try to run an LDAP sync.The problem has just started occuring and the only change that I know of is additional users in Active Directory.I have sent off an email to our cisc...
One of my offices uses call accounting codes for all long distance calls. The codes are setup by the provider (Sprint) and the usual proceedure is when the call is routed to the office's long distance PRI, a beep is heard, and you enter in your 4 dig...
Hi, We are planning to start replacing avaya PBX with Cisco IP telephony but we have to run a small pilot showing the capabilities of the Cisco products. Right now we have G650 gateway and S8700 server. All PRI lines are connected to G650 (with CLAN ...
