Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,I am trying to integrate a CUCM 8.5 environment with a Siemens Hicom 300 PBX using a H.323 gateway and a QSIG PRI. Everything appears to be working as expected except one thing: When I call from a Cisco phone to a Siemens phone, the name of the...
Is there a way to select which phones can use Fallback in case you have more than the max-ephones allows for?
I had just deploy a CM8 and I found that when I have a internal call from extension to extension, the caller hear a short "du" tonewhen the call is offhook. Anyway to disable this tone?
Hi,I am getting an error message while installing cisco call manager 8.0(2). The error message is given below:The installation has encountered a unrecoverable internal error. For further assistance report the following information to your support pro...
Hi, I currently have CUCM 6.1.2 and are looking to upgrade to 8.5. However, in order to achieve this we need to upgrade the memory and HDD to accomodate the upgrade. I therefore need to know the specific server make and model so I can order the corre...
HelloWe have the following config and have configured a num-exp command for external access to voicemail. When callers call from external to access their voicemail, it seems DTMF tones are not being passed. I have attached output from debug ccsip me...
Hi All, I currently have a customer that is having some trouble calling a into there Cisco IPT system. When an external users calls into the system e.g.456-1234. Some would reach the operator (which is correct) while others would only keep hearin...
Hello,I ran into an issue with Cisco 9971 camera. We have CM running 7.13.32900-4 code and I installed devicepack 7.1.3.33204-1. The phone itself is able to detect the camer and I am able to preview the video on the phone, However CUPC (8.5.1) is ...
Hi all Is it possible to upgrade firmware on Cisco IP phone7902G without CallManager. On the phone is software version 1.01(030313A), and the phone doesn't work properly.The phone register on CallManager but it can not pick up new firmware witch is 8...
I have a 7962G with 7915 expansion module. I have a phone button template of 5 Lines/1 Intercom/ 12 BLF. None of the BLF buttons will light when the designated dn is on the phone. The button will work as a speed dial just fine.Suggestions/thoughts??
Hi,I need a Info on Cisco CCM.The requirement is....I am calling from my IP Phone " A " to a PSTN phone " B "I have directory number on my ip phone for example 80382XXXXXI need when the calls comes to my phone through PSTN i should not get the actual...
Hi. Could anyone help me? How Can I secure Auto Reassertion in CUCM 5.1, everyone who installs IP communicator in our company can register to system , Can I block IP addresses on firewall or Call Manager? or can I block exact Phones by Mac addres...
Hi Please let me know how to enable option to listen to the call using both headset and handset at the same time in Cisco 7942. I am able to do the same in few cisco 7942 phones but not in other few. Not sure what is to be enabled to have this option...
Dear friendsi have got a phone on which the voice mail greeting is playes for 3 times then it goes to beep for recording. it rings normal for 30 seconds as configured then it goes to voice mail but playes the greeting 3 times. same lines. this is not...
Hii have a unity server that i have set to answer a incoming call and then transfer to an operator.To test i have just set it to transfer to a standard ip phone. My problem is everthing works until the call is transfered out of the unity, where it fa...
