Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Is there any benefit to compressing the control traffic o\ver the WAN. Have a customer who is investigating WAN acceleration boxes and would like to know if compressin VoIP control traffic is beneficial.
I have a customer whose host site was affected by a tornado recently. The host site is pretty much flattened, and they are unable to get to the site to assess the damage. Anyway, they have a remote site that is in SRST, and the site is working fine, ...
Hi Engineers,One of my customer has a requirement ip tel connectivity through remote connection.(DSL)They thinking a cheaper solution which is DSL(CONFIGURED VPN).The remote phones will register to a single site.Could you please let me know if there ...
My CCME often has one or two DN get hung. No tones come out of the phone. I tried to remove the DN but got the message: 'DN 2 has active call on interface 50/0/2 CH1.Cannot unconfigure'. My only solution is to reload the CCME. Do you have any better ...
I have configured my UC520 in hybrid mode with some phone having buttons for DNs configured as trunks and other phones having to dial "9" to get a line. With this setup if an phone configured with a trunk DN picks up the line all other ephones using...
Anyone seen this? Original call gets placed on hold when another external call comes in? This only happens to our 7941 phones?
Hi We have Call Manager 3.3(4) connected to a standalone MOH server. Everything works fine expect when people call into our offices on cell phones and are placed on hold. They report that the MOH stream breaksup/generates static for them. This issue ...
Hello Folks,The 7965 phones don't show up on my CM5.1. I have installed the latest ES (cisco-ipt-k9-patch-es5.1.2.3104-1.tar.gz.sgn)for the CM5.1 and also installed "cmterm-7945_7965-sccp.8-3-3.cop.sgn" as the load to support 7965 phones. I have rebo...
I am looking for assistance or pointed in the right direction of setting up conference calling in CUCM 6.1, with 2811 running in SRST mode.I have a remote site registering to 6.1, with a local ISR running in SRST mode. I do not want to set up a medi...
I have a site in rural Kentucky that is serviced by copper DIDs. In the past, inbound calls via the DID trunks were delivered correctly to each telephone AND if unanswered would rollover to Unity. Today, the calls ring the appropriate phones but th...
I have configured an ATA (FW: 3.0.1) with dual-line in order to provide call transfer capability. But when the first call is active and the ATA receives another call we have very bad audio quality (it is impossible to keep the conversation). Has anyb...
HiThis is a new config to move from SRST to CME-as-SRST (c3825-adventerprisek9-mz.124-15.T4). I want the following done when router falls back to CME-as-SRST mode. I already setup the configs but we will test. I need a sanity check to see if this wor...
I have a 2811 with PRI running SRST.My telephone number range is 555-389-0800. I am recieving all 10 digits from telco, and am using 5 digit extensions. Since the first digit is a 9, I created a translations pattern in CCM so that extensions are 80...
Please help me I know how to manually assign directory number to analog phone on analog port on VG248 FXS by calculating MAC address with CME4.0(2). But when need to do with router 2801 with VIC-4FXS/DID card I do not know howI try with ephone-dn 13 ...
Hi a strage problem. I have a SIP phone behind 1812 configured for VPN to central office (PIX 7.2). This phone registers and can commincate with central office very neatly. When this phone calls another SIP phone behind one more VPN (using 5505 or st...
