Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi I have my legacy PBX with limited analog phones and looking to deploy CUCM for more capacity, i found cisco VG350 supporting traditional analog devices on IP networks. any advice to deploy this integration.
Hi Folks we are setting up a new ASA Proxy service for registering IP Phones from home users. We have just figured out that the existing CAPF cert on CUCM is expired for a couple of years. Our existing CUCM cluster does not operate in Secure mode. I...
Hi all i have 2 VG224 connected in ip network I have attached fax machine with both vg224 i need to know how can i configure vg224 for fax Thanks Your support will be highly appreciated
Hello, I'm in a lab environment and I'm configuring an ISR 4321 using MGCP protocol. My ISR has a NIM-1MFT-T1/E1 module which is currently down (I don't have an operator link my lab). The problem is TFTP download failed on my router : router#sh ccm-m...
I am trying to remove any reference to the T1 card in 0/3 before I shut it down and replace the card with a FXS card. How do you remove the 'Controller T1 0/3/0 and 0/3/1?? It is a two port card. I have shut the controllers down, and I have removed ...
I have a customer's phone system that has an attached IVR. Essentially, there is a 3rd party SIP device installed on the phone system. Calls to the IVR get routed to this SIP device's number and the IVR monitors it and "picks it up". There are no ...
Hello, I have one issue is that the CUCM Media resources are not registering, the media resource of the publisher server keeps getting unregistered -> rejected then registered, go back to unregistered after few seconds. Publisher MTP and other reso...
Installing our first Jabber on IM&P Version 10.5 and expected that Jabber might be a plug in that you download from the cluster. Not the case, or I could not find it. Downloading it from CISCO however, I get a version that seems to want an email a...
We have a CUCM version 10.5 in our regional office. We also have a remote location that uses our regional office CUCM for call set up/tear down but has their own local gateway and PRI, equipped with Cisco Unified Survivable Remote Site Telephony (SR...
Hi Can somebody please help me solve this issue: Error Message = Call failed: Maximum call-per-line limit r...... I am unable to transfer calls after the call has been placed on hold, however can transfer the call if it wasn't put on hold first. Thi...
Hi , we're looking to upgrade our estate from 10.5 to 11.5. When I look into PLM I notice that all the licences have a (10.x) next to them. My question is does a CUWL (10.x) licence for example work with a 11.5 CUCM.I'm guessing not maybe but as a ...
I tried configuring Cisco 7931 phone for use with FreePBX . I upgrade the Cisco 7931 to firmware SIP31.8-5-3SR1S. I tried Cisco 7931 to register with FreePBX but with no success. Cisco 7931 phone time not synced. I tried the NTP line settings in ...
description * * * Not In Use * * *!voice-port 0/1/0 connection plar 222033436!voice-port 0/1/1 connection plar 222033437!voice-port 0/1/2 connection plar 222033438!voice-port 0/1/3 description * * * Not In Use * * *!voice-port 0/2/0 description * * *...
hi All, We have an production voice gateway with E1 which talks h323 to our CUCM. We have just inserted a 4port FXO Card and we would like to route only all our mobile phone calls to it. I am getting conflicting info by searching the forum and also...
I am trying to configure Branch router for the customer to have : 1) AA from unity connection as Primary 2|) User Local TCL script AA as backup in case of primary failure. when i try to call the main number , the Local TCL AA ALWAYS start even ...
