Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I am using firmware 11, but seems buggy. Is 10.3 recommended for use with CME10.5? AT
Hi, I have used self provisioning several times now and in general it works very well. I now have a situation where we have a new system where all users will use Extension Mobility. Is there a way to use self provisioning and create automatically a U...
Hi I have multiple CUCM 9.5, these are distributed over the WAN in around 34 sites. All these locations have PSTN calls from the local site gateway. I have existing billing server in our HQ site only for the HQ CUCM, we would like to incorporate o...
Hi, Is there a way for applications that require Cisco TAPI to point to more than 2 x UCM nodes? ie CUAC Standard, 3rd party all recording Thx
Hi , We have an IP telephony setup running on CUCM version 10.5.Our client has new requirement which is mentioned below.Client don't have Unity. For example User A using IP Phone which is registered on CUCM.If someone call User A and if User A is bus...
I am trying to implement SIP EO on trunk from CUCM to CUBE.I enabled SIP EO in sip profile (Insert MTP if needed)To test I use CIPC version 8.6.5.0.I notice diffirent bihavior when calling from CIPC over SIP trunk.When I enter number and press DIAL b...
Hi everyone, If I am able to calculate the number of UCLs I need when migrating from DLUs to UCLs, is it enough to create a request via PLM and send the request to Cisco without a report from the License Count Utility?
I am migrating the current 8.5.1.10000-26 to virtual platform with ESXi. On this case the MAC will be different so I would need another license file. But is possible download the current .lic file from the physical cucm? I have found only the option ...
Hi I have CME with two IP Phone IP Phone1: 172.16.15.5 CME: 172.16.15.6 IP Phone2: 10.10.10.2 IP Phone2 have 10.10.10.2 and after NAT have 172.16.15.8, the problem I faced is the phone 2 can ring but not receive any Media only send, How I make Pho...
I am working on a system where they have 1 analog line plugged into their H323 gateway, we have set the caller-id enabled on the FXO port and when we do a "Debug VPM Signaling" we can see the caller id of the phone as it hits the voice gateway. Howev...
Hi It looks like only one softphone can be installed on one PC. I tried to install two, but failed. How do you think about it?
Hi How do I set buttons with numbers or personal extensiones. As speed dial. Model 7861 phone Regards. http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cuipph/7821_7841_7861/10_1/english/user_guide/PA2D_BK_UB7EF0F0_00_user-guide-7821-7841-7861/PA2...
Hi there we are looking for a setup to get the following workflow, we are using CUCM 10.5.2 and Jabber Clients 11.5.1 for Mac -> we have a pickup group "dept-a" with 5 members. group pickup notification, pickup as such works fine.if one of the member...
Hi everyone , i need help to resolve the issue (i have router c2851 with 4FXO and nme(Cue 3.1) +cme )what i need if any income call from pstn, the caller he listening the specific message audio and after that transfer him to internal number in my net...
Dear All, The gateway is mgcp. The phone behind it has number 4082022002. When making a call at 2002 and 2022002, the phone can get a bell voice. but if making a call at 4082022002, the phone cannot get voice, but I can get it debug message as below....
