Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We need to add Cisco DX80 and DX650 phones in CUCM 10.X ,Please advice how to configure and share any documentation if any. Thanks in Advance... Regards,Ramanathan
Hello I have an E1 and I would like to know how I can see how many digits its sending? Thanks all.
We have recently changed from ISDN to SIP and have noticed a difference and need some help clarifying this. example:previously --> Any external number 444000(e.g mobile etc) calls deskphone 555000 which has a forward to their mobile. On their mobile ...
I am having an issue that I can't quite solve. I am new to Cisco UCM so please bare with me. Essentially the issue is when a user forwards their line to their cell phone, or any external number, and that number is called from an external line, the ...
We have a backup connection to all our remote sites via a GRE tunnel using the Internet. We have QoS in place on our primary MPLS circuits to prioritize our voice traffic however I was wonder if applying QoS to the backup GRE tunnel would work as we...
Hi Guys,We are upgrading 3825 router to 2921. The old router has these enhanced modules EVM-HD-8FXS/DID and EM3-HDA-8FXS/DID where total 16 FXS ports are configured.Can those two modules be moved from 3825 and attached to the SM slots of 2921. Will t...
I have a scenario where I can dial the DID on a 7841 phone dial the extension and both workFrom that phone user can dial my extension and that worksWhen that user tries to make an outbound call to an external number they get a fast busySite is using ...
I have installed a 2911 router with PVDM , There is a problem that no voice commands are accepting............Telephony service , ephone,....commands are unrecognised commands..... Note:-The PVDM0 light is orange ( is this a hardware fault or softw...
we have 2801 router that connected with 2 anloga lines (FXO Card), but now we have a problem with disconnect problem, the phone still connected after the PSTN Caller Disconnect, and our policy tell that the agents shouldn't end the call, so we want w...
All, I'm using a Cisco router running Call Manager Express (if you can't tell its somewhat dated) and would like to set up an FXO trunk to ring into the system and then if no answer, ring to a SIP extension/trunk to the third party SIP voicemail syst...
Hi all I have a E1 configured as R2, and when I do an outgoing call to any number I dont see the phone number that is calling. I only see Private Number. Thanks.
Hi, has anybody implemented HSRP with a CUBE pair? CUBE 1 is .1 and CUBE 2 is .2, HSRP is .3 Calls ingress from the ITSP to the public IP, natted to .3 but the CUBE tries to reply with .1 instead of the HSRP address. Is it possible to implement HSRP ...
We have a problem with a headset (Plantronics CS540A), to active the option Wireless Headset Hookswitch Control on a phone Cisco 6945 with the CallManager. We do not find the option "Wireless Headset Hookswitch Control" in the phones settings on the ...
Hi, I have installed, CUCM 10.5 with unity and presence in office recently. Everything works fine and good. My manager initiate a request to have Voice message broadcast facility on his telephone set. He is using Cisco 8945 phone set Any advise.
Hi guys,I have a question to ask. I got to deploy VOIP for my customer. In the architecture I have 3 sites:- One CME 2951 srst which become the voice gateway and one Cisco BE6000 on a Headquater.- A srst cme for each of the two remaining sites.Can we...
