Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,for a few extensions of our CME installation we would like to supress the sending of the outbound CLID to the outside world(the system is connected to an E1 PRI).Normally i would do it via the outbound translation rules, but the user may want to d...
I have a really strange situation. I have a 7931 IP Phone that anytime you dial a number with a 4,5,or 6, it will automatically dial one of the BLF speed dials. It doesn't matter if you start a number with a 4,5,or 6, it can be in the middle of a p...
Is it necesary to buy multisite license for SX20 in order to install 2 units (sites)?
Dear All I have CME , I have some questions :- where i will configure the greeting like in CME or CUE :" welcome to the XX company if you the extension press it now or , 1 for sales department , 2 for Maintence department " and this should be in ara...
When we enable secure RTP and TLS for signalling; is there any delay in voice; does latency requirements changeIs there any other recommendations/best practice documents available for same.Thanks
Hi,According to the compatibility matrix ( http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/compat/ccmcompmatr1.pdf ) the default firmware in CUCM 9.x for 7940 and 7960 phones is cmterm-7940-7960-sccp.8-1-2.cop.sgn. However, when I go look at the l...
HiNew install with SIP trunk on 2911 and using ASA for RA VPN Client. I can register the softphone fine while connected via the VPN client, can make calls and can hear the end party but they cannot hear me. Using anyconnect client (windows 7 no fir...
Dears,sometime in a day when i dial to pstn it gives me fast busy tone then again when i dial again it gives me fast busy tone i have to wait for 15 to 20 sec and when i try it works fine but this happen intermitent, and also sometime the call are dr...
Hi We are planning to use SRST inside of VRF, can you please share any limitation of this implementation, and Cisco recommendations for this ?Regds$
Dears,The below translation profile is for outbound calls from the corporate which is having a 8 digit numbering plan the result for below translation profile is the digit which will go to ITSP are 8.. This means ITSP is accepting only 3 digit from m...
Hi there,I am trying to find out a SRND for this appliance. Need to find out how these two servers act as a fully redundant set up, so questions are;2 x Servers running ESXi - I would assume these act as one server in a vitual enviroment?CUCMBE, Unit...
Good day!Can you help me please, im trying to create a custom ivr vxml scrip, but i cant make it to work properlyWhen ccme receives a inbound call:1) Welcome greetings begins to play (It works properly)2)Then, if smb enters ext ... connection should ...
Hi all,Yesterday I moved phones between clusters, now we are facing with busy signal issues on 7942 phones. Connection is establishing sucessefully, when it comes to RTP session it gives me a busy signal tone. On 7911 phones RTP is working fine.CUCM ...
Hi all,We have cucm 8.6 and 6945 ip phone .Users r not able to do confrence call between internal or external user.Point to point call workingfine.but when they want to mske confrence call it disconnect Kinfly provide me a needful solution
HI, a strange problem met in these days IP PHONE 6921 register failed when connected with master stacked swtich which configed with 802.1x but fine when connected with other switches in the stack the running config has been post as the a...
