Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Guys,I have a cubac directory that refuses to sync. It does 100 or so contacts then just bombs out.The log just shows:Cisco Unified Business Attendant LDAP Plug-in, Machine EUDC1PCUBAC, Build 8.6.2.123CONTACT_UNIQUE_REF CONTACT_TYPE FIRST_NAM...
Hi I need to register 3905 phone with CME 9.0, how can i do this ? I create a sip pool and create an username and password, how can i set this credentials to phone ?Do i need to load any additional files to CME ?Regds$
Dear All,Weird issue.. I have a E1 PRI line on a 3925 MGCP gateway to a CUCM 8.0.3.Outbound calls does not reach the gateway at all.Inbound calls reached the gateway, rings for max 1 sec and then disconnects. the ISDN Q931 debug shows the following -...
Router is 2821 with DMS-100 PRI in Canada (no TCAP DB here). I am receiving NOTIFYs with Connected Address & Display IE's from the switch. This info is relayed to the CUCM in MGCP mode but not in H.323. Is there a way to get Called ID updates on th...
Hi everyoneDue to a migration of CUCM 7.5 to CUCM 8.6.2About 2,800 6921 IP phones were using firmware 9.1.1.To avoid a massive upgrade to firmware version 9.2.1 that comes with CUCM 8.6.2, it was installed firmware version 9.1.1 on the TFTP and this ...
HiSomeboy knows a tool (non-Cisco) to assessment of CallManager?Best RegardsPeterson
Hello guys!When upgrading a Cisco 2921 that already has UC and IP Base technology packages installed from version 15.0(1)M6 to version 15.1(4)M5 it is necessary to upload the licenses after the upgrade or licenses will remain the s...
When i try to add a new ephone in CME, i get this below error.Error: Line mode can't be changed, need to remove the dn and reconfig again.Commands entered for the ephone creation:ephone-dn 15 dual-line number 3250 label Phone A-3250 description 3250...
Hi team.I have a doubt respect to upgrade the CUCM system from 7.1(5b) version to 8.6 version.The "Cisco Unified Communications Manager Software Compatibility Matrix" show that the upgrade from CUCM 7.1(5b) to CUCM 8.6 is "Direct Upgrade", but I don'...
Is it possible to get CME to transcode between a SIP endpoint and SIP trunk? If so, it seems virtually impossible to get it to actually invoke the transcoder even when there is a codec mismatch.We know the transcoder works because it gets invoked e.g...
Guys,I have installed UCCX 8.5 su1 in vmware player. It installs fine and evrything works. However the moment the machine is powered down, and powered back up, it becomes unreachable. You can no longer ping or connect to it via http.When this first h...
Hello,I got SRST working on 2921 we have for a WAN location. We have two PRI's at the location and all DID's are held at that site.Phone calls in SRST are working fine inbound and outbound.My problem is that when I call a Cisco IP phone that is in S...
We have a remote office in Hungary with a vpn connection to our data center and we are trying to see if we can get an IP Communicator to work in that location. The end user in the location sees the phone trying to register and fail...
I need to have this enabled in CUCM7. I see it's a function available in CUCM 8.6 GUI in the SIP trunk config, but not in CUCM7 . My call transfers are having one way audio issues. My SIP provider said to try to enable this fuction...
