Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi , Is 7925g Support cisco 1841 CME router ... i found type only 7920 and 7921 in the router.any help will be higly appreciated
Is there a way to change the reply-to address on UCXN 8.6? I have a lot of users who tend to reply to the voice mail notifications delivered to their inbox. For example if I call and leave a message for someone, the address that it sends from is kknu...
Hye Guys,Need help, a client already has a Tannoy system and we are putting a Cisco system in. How can we integrate a Tannoy system with CISCO it will be a great help if you can advise on this matter.
Guys,In cucm 7.x you could run the command below to check the filter that is applied to your LDAP sync. admin: run sql select ldap.name, ldf.tkldapserver as type, ldf.filter from ldapfilter as ldf inner join typeldapserver as ldap on ldf.tkldapserve...
Hello,I am looking for a UPGRADE PATH from Phone Load: SCCP41.8-3-1S (currently phone with active load working on below version of CCM) to SCCP41.9-2-1S. Please suggest resources. Thanks!Model: CP-7961G-GECUCM Version: 8.5.1.14063-1Regards,Karthik Sr...
What I have is multiple sites with the same number. For ex. Lab at all the clinics are 1246 and let's say foot clinic at all locations are 1358. My problem is a user at site A calls a user at site B, say 1246 calls 1358 call manager won't know whic...
Hello Huston, I have a situation,A client of mine implemented direct SIP trunk from their CUCM 8.5 to their MERA softswitch.They set MTP required, cause doesn't work otherwise.MTP is CallCount = 120 on each CUCM (2 of them in cluster)We have certain ...
I've got a 7920 ip phone that i'm trying to register with CUCM V. 8.0.3.20000-2. I've got the profile created on the CUCM and the 7920 connected to the AP. The 7920 cycles through Configuring IP network, Downloading Config File, Connecting to CallM...
Hi Guys,I am using C881-CUBE-k9 router and would like to register 2 SIP lines from the same provider, currently I can only register one. Any suggestions why I cant register 2 SIP lines ?Config Attached:Any help would be really appreciated.Thanks
My IPC Clients are tryign to register to Call Manager Express V7.1 and can't find this filecan anyone tell me where I can get that file and where to put it on ccme?CTLSEP(Mac Address).tlvThe ios is C2900-universalk9-mz.spa.150-1.M8.binthank you
I need to record the voice calls of cisco IP phone 6945can anyone tell me about Application that is used to record the calls. Try it use wireshark as sniffer tool and decode it but it doesn't works..Plz help me..
CDP is disabled on the switchport of my 7941 phone, but it is enabled on the PC port. Is there a way I can reenable it from the phone?CDP is enabled on the switch and is finding everything else just fine, just not the 7941 phones.Thanks
I currently run a 2901 in a remote location running through the CM in our corporate office. They since have requested running a virtual rightfax machine through that gateway. I was hoping I can have the rightfax server go straight through the GW with...
what radio model do you recommend to use with the IPICS? I just want to make some tests, so I don't want to buy some expensive radios. Any clue would be helpful.
I've found a specific issue with these two commands in SRST (Call-manager-fallback) use. The use of the Translation-profile command within the Call-manager-fallback section allows the manipulation of digits/strings to/from the SRST source as per thi...
