Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
hIWhen i runn the CDR reports it show internal ip phone to ip phone calls also.how i can stop this that in my CDR report i dont want to see internal callsThanks
Hi guys,why doesn't the CME permit 2 SNRs on 2 different lines? it says: "DN 1 is also SNR. Can't have a 2nd one with DN 2".Example:ephone-dn 1 dual-line number 100 mobility snr 001234567890 delay 0 timeout 60ephone-dn 2 dual-line number 200 mobili...
i'm installing ICMH's NAM When i install NAM logger on server the IE auto shutdown and on my PC i open IE install logger the IE no responsesomeone help me please !!
Hi all,I have a conference station, but I cant see the version in either, the configuration screen on the phone and the web page of the phone. for that reason I can not make this phone to register with the CUCM 7.1.3. I reccently update our CM and (p...
Hi,I am running here CUCM 7 in HQ and some branches IP PHones are registered with that. Also I have CME running in some other branches. What I have noticed is RTP traffic is flowing not between CUCM and CME endpoints. Instead, traffic flow from CME e...
Anyone done this ? I believe cisco sell call recording now - any pointers ?The configuration on the Call Manager / handsets is well documented http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_5_1/ccmfeat/fsmr.htmlAny pointers to the actual ...
Hi there,i have some problem with 9951 ip phone, i plug poe and when started, after cisco logo, the phone screenis stack in blacky dont know what happend, what is the key sequence for factory reset on ip phones 9951, is the same that all other ip pho...
HelloDoes anyone know whether it is safe to reboot a subscriber whilst the publisher is offline. The situation is that the Publisher has suffered a hardware failure of some kind, probably it is the PSU that is broken.All phones are currently register...
Hello,I have a cisco 2921 which i added to it a VIC2-4FXO card, i can see the card in the "show diag" from the CLI,but i cant see it on the CCP in order to configure it from the CCP. Its not the first time i add a card and it doesnt show up on the CC...
Guys have a client with CUCMBE 7.x and some recentley added 7945 Handsets.I have installed the 7945 device pack as per usual and it works fine, however when I try to add a user through User Management > User/Phone Add the 7945 Phone isn't available u...
Dear Community Members,I have the follwing casual scenario: (ext2000+CUCME)-----IP----(ext1000,1001+CUCM). Calls between 2000----1000 and 2000-1001 works fine. From CUCME side to CUCM I am using dial-peer voip with codec g729. And CUCM was CUCME poi...
Hi,I have an environment running CUCM version 7.1. I have successfully created an End User in CM and just could not find an entry being created in Cisco Unity Connection after that.Any solutions would be very much appreciated. Thanks.Regards,Mohammed...
Hello Team,Good afternoon !In this document : http://www.cisco.com/en/US/docs/telepresence/endpoint/software/tc5/release_notes/tc_software_release_notes_tc5.pdfPage 6, it is said that we need CUCM 8.6 to run EX-60, but we have at this moment CUCM 8.5...
Can someone give me guide line for the subject matter. Thanks
Dear All,I am trying to connect CUCM v7.1 to a provider who is using H323.Outgoing from CUCM is working okIncoming not working (DID extension rings, connects, but no audio and get disconnects after 10 seconds, main number connects but no voice greeti...
