Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello there,I have a new install of unity connection and we are turning on the single inbox with exchange 2010when you test the unified messaging section it comes back with no errors.however when you test the unified messaging section under a user it...
HelloPlease help. Currently we have a Cisco 2960 switch connecting to our Dell Equlogic Ps4000x and 3 R710 Esx Hosts. However I have no switch redudancy etc using one switch. I would like to connect another switch (stack) if possible but am not sure ...
First:Cisco Unity Connection version: 8.6.1.20000-109 CUCM: System version: 8.6.1.20000-1I have an issue with Unity. Whenever I dial an extension that has a VM box, instead of transferring into the called numbers box, I get prompted to enter my PIN ...
Hi, we are going to move a server, so when we shut it down all the phones will register on the next subscriber, but, we we switch it on again, they will come back or they need to be reseted?Thanks in advanceCesar
I have a phone constantly configuring ip, the por its ok, no issued with dhcp, i have tried different port, cable, i had tried the phone in a different switch and everything its ok, the mac doesnt appear in the switch throug cdp, and the show power i...
Hi everyone,i want to place order for an ip phone(cp-7911g) of 250 unit and i have media convergence server (mcs 7800 series).how many number of device license unit(Lic-cm-dl-10=) will be required?how many dlu will each phone(cp-7911g) take?brsamson
HI!I have to configure basic functionality for TCL IVR in ISR 2900 G2. Is it necessary to buy FL-VXML license or basic functionality can work without it?
Hello,I have CUCM 5.1.3 i wanna upgrade to CUCM 8.6.2 what are the hardware requirements, i didnt found the documentantion.Thanks
HiI am trying to upload users and phones using BAT. But when I gave for validating it gives me an error "Device Name/MAC Address Error Code Error Description".So I am not able to add the users and phones using BAT.Insead I tried to upload phones and ...
Hi,We installed a AIM module in cisco 2811 router. After installation we cannot access the module. Wheni issued Sh diag i can see the module status but with error. (AIM2-CUE-k( are not supported for use in AIM1(slot 1). Any solution to make it work?T...
Hii have call accounting enabled on uc520 configured to file accounting, the file created on ftp has a size of 0k, the one on flash is goodmy config isgw-accounting file primary ftp 10.22.64.201/uc500 username cdr password cdr1234 secondary ifs fla...
Can we use multiple codec for the ephones, I mean can we assign one codec for each group of phone in CUCM ver 7.1.3.Is there an appropriate codec that fit the wireless radio network, so that we can assign one codec for them, and one for the wired net...
Hello,We have call manager 8.0(2) and this uses SBD. I'm sorry if this sounds like a bit of a daft question but we have a number of clusters and we need to be able to move the phones from one to another without having to delete the itl file most, if...
We havea call manager that was setup by a vendor. They left a cisco switch and AP. Which does the following: We Power a new phone- it connects to the 'cisco' ssid and pulls down and applies config from WLANDefault.xml file which it pulls from the TFT...
Hi Experts,In my lab, I am upgrading our UC from 7.1.3 ot 8.5.1. The ISO that I am going to upgrade to is:UCSInstall_UCOS_8.5.1.13900-5.sgn.iso I am receiving a message stating" This Refresh Upgrade will COMPLETELY REFORMAT YOUR SERVER. Reverting to ...
