Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have CUCM 7.1.3, I need to update line settings for almost 2 thousand selected records, is it possible to use UPDATE the line settings by using a CSV file , in CUCM BAT, the only option availabe is to select by query, however that's not an option f...
I have this problem about failure displaying caller id on ephones, on CUCM the checkbox for caller id on analog ports is enabled, so when I have an incoming call the caller id is displayed, but after some minutes, don't know why, the caller id is not...
I figure the Bulk Admin Tool is the way to go but I read the link here:http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/bat/5_1_4/bat_phon.html#wp1188864and that's not very straight forward relative to what I know I need. I have a very simple need...
I'm getting replication status error message # 3 between our Unity pub and Sub servers I have run the following form the pubUtils dbreplication statusCopy current replication file and receive the error Pub status is 2 active local Sub status is 3 act...
Hello, My cluster has server software conference bridges (created by default during installation, of course) and 3 hardware conference bridges that I created on my three voice gateways. Everything is registered fine. When I do an "show sdsp...
Hi,I am using CME 7.1, the system is configured with all the incoming calls goes to operator extension 3401 and there is no voicemail option for now. The problem I am facing when we are getting more than one call, the caller gets the busy tone. The o...
Hi;I recently installed a UC320 and SPA 303 phones for a client but there is a lot of noise, interference;and cross talk on all the calls;On top of that the admin password for the router setup is lost and the techinician that setup thesystem quit.Yes...
Hello, I am working on installing g729 phones in our environment and they seem to be working fine;1) Calling any G711 phone2) Recieving calls from PSTN3) Recieving calls from CRS 5.0 However, they can not recieve MOH when two g729 phones call...
Hello , Could some one advice , what i need to do to erradicate these error messages;CME-C2851(config)#tftp-server flash:Desktops/320x196x4/TN-Dak.png File with same name already being servedCME-C2851(config)#CME-C2851(config)#tftp-server flash:Deskt...
Hi. I have a Hypermedia HG3000 GSM <-> PRI gateway. The gateway is loaded with GSM SIM cards and hands off a PRI to CME (15.1(3)). Outbound calling through the gateway is working fine, however when i call in to one of the DNs associated with one of t...
Hi,I'm looking to find a better solution to my current incoming call manageability. I currently have the lines of 10 people presented on one phone, and if any of those people's lines don't get answered, the call rolls to another line, let's call it L...
Does anyone know if this is possible or have they done this before:When an IP Phone goes off hook, If no digits are dialed then send the call to an extension/security instead of getting the re-order tone.They are asking in the event an employee is se...
Hello all, I have a customer who ordered a cisco 2821-CCME/K9 router to function as call manager express in his network. Am a newbie to voice and I wants to clarify something regarding the license. in the description of the router I have s...
I have been receiving this particular error code for extension mobility .After checking this code it tells that Cannot connect to EM ServiceLOGIN_SERVICE_CONN_ERROR—Unable to connect with EMServiceThe solution given by cisco is that restart EM servic...
*Aug 2 08:32:09.291: //-1/xxxxxxxxxxxx/MGCP/mgcp_check_hostname(8901):[lvl=0]Trying to validate endpoint name
