Cisco 7821 has a blank screen as shown in attached file. What I have tested so far:1) Upgrade phone firmware to 10.3,11.5,11.7.12.52) Pull good working lcd from good unit to replace bad unit phone3) Ip Phone can register to CUCM 11.5 as normal None o...
I did lots of thing and I read alot about the configuration but I have this "ERROR: Zero Size Tracks" problem let me explain the steps : 1.I create the sip profile with the " deliver conference bridge identifier " check box enabled.. 2.I check "...
I have been trying to install NME-CUE with SM-NM-ADPTR on C2911 Router. I can get to the console of the CUE and get the following on the console:=============================EIST: Built Mar 3 2006, 14:49:27UsbHid Pwd Msg0 Msg1 Cache1 Mem2 Prot Cache2...
I was looking for the G722 codec choice in the web-admin setup for the SPA-112 and I don't see it. Several searches on the web seems to indicate that this ATA does have it but I don't see it. I see G711u, G711a, G726-32, G729a (just those 4). I h...
I have Cisco Unified CM AdministrationSystem version: 11.5.1.14900-11 I have a request from a manager for a phone utilization report. There is a CTI route point number setup for a group of users to pick up the calls for the department. He wants to kn...
Hi erverybody. I´m configuring a ISR 4321 and when I test softphone registration from other branch via VMVPN I can´t get full register. I do a debug tftp events and tftp packets command and see following: Oct 19 01:18:25.639: TFTP: Server request fo...
I am quite annoyed to see that the Cisco BE6000S is going EOL in 2022. We JUST had this stupid thing installed in 2017 and I now discover it has only a 5 year lifespan before Cisco is forcing it into obsolescence. We are not a wealthy enough organiza...
I have several Cisco 8845 phones which I have been able to configure for SIP accounts via XML and TFTP without CUCM. I would like to configure a custom background image. Is this possible without CUCM? Could someone point me in the right direction? Al...
All, I have an inbound DDI delivery via a SIP Trunk, this DDI is matched in a dial peer and sent into CUCM. CUCM then has a match for this as a CTI Route Point which sends the call into CCX. When I dial the CCX trigger internally I can get through al...
Hi. Would somebody can recommend how to use a Custom ringtone on a single phone in CUCM 11.5. I know that Cisco IP phone designer doesn't exist anymore so what alternatives do I have? Any suggestions? thanks
jabber problems using iphone when jabber has in the background screen we could not turn on. Only when we leave jabber open do I say in the foreground that the link works. Is there any way to solve this?
Good day expert. I have an issue 1. My service provider says my CME is not registering issue is the have give me 2 IP addresses one they say is for signalling the other is for media? now which one do i put under here dial-peer voice 4000 voipsession...
HelloI have a 50Mb UP/Down fiber service. We are getting sip trunks over the internet and need to set up Voice qos on the wan side.
Hi community, User makes external call but cancel the call getting no answer.If the user cancel the call, CUCM v10.5 sends sip CANCEL to the telephony provider.But this CANCEL does not contains Reason Header with cause code. Here is example:CANCEL si...
I've inherited an environment with about 30 Konica-Minolta MFPs with faxing. Our monthly recurring telco costs for the analog lines are approx. 2,000 / month. I'm hoping to get real customer input as to how they have eliminated their dependency upo...
| User | Count |
|---|---|
| 8 | |
| 7 | |
| 4 | |
| 4 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
