Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Some Ip phones can not log in and log off even when requested by CUCM. In CUCM appears the message "Error occurred while retrieving information from database. No LOGOUT device profile". In IP phones the message is something like "error 6". The CUCM v...
I have an NEC 2400 IMX connected via a PRI to a 2851 series router which in turn is connected to UCM 6.1 via MGCP. 4 digit dialing works great between NEC phones and the ip phones. DID calls into the IP phones work great. However, when I try to ca...
UCM 7.0 w/ ldap integration. Has anyone used the SDK to modify the telephone number information being displayed at the ip phone in the corporate directory to prepend a 91 so the edit dial softkey is not required to complete a call to a number in the ...
I am running a backup for UCM and it is hung and refreshing I tried to cancel it and it is still hung. THis is what I am gettingCCM DAB-UCM-PUB1 TCT 100 SUCCESS Wed May 27 11:19:24 EDT 2009 2009-05-27-11-19-24_b_dab-ucm-pub1_ccm_tct.log CCM DAB-UCM-P...
CUCM 6.1(3). Four route patterns beginning with * and all are set to provide outside dial-tone. There are no other patterns in the system beginning with * yet the dial-tone plays after the second digit is selected rather than at the first digit press...
I have a centralized CM 6.1 with two remote sites connected via VPN. The one site is having bad call quality on all calls - doesn't matter if they come in the pots or voip. Not sure why this is happening. When a call comes in local pots I plar to ...
Hi. I'm running CCM 5.1.2 with CAR enabled. I am trying to get a fairly simple report but am new to this and having trouble getting to the right place.Basically I need to know the number of external calls are coming into all extensions. Only external...
Hello All,Does anyone know how I can update my DSP chip to work with a 2801 router? I have a PVDM2-32 in slot 0. Upon the router bootup the PVDM2 module does not go active. when I do a show voice dsp detail, I get the error message: "in slot 0 are us...
Hello - Have been running CallManager 5.1.1.2000-2 for about 2 years. Have a primary callmanager and secondary. When it was set up the default callmanager group had the primary listed first and the secondary (subscriber) listed second. So - all d...
Hi,My organisation have asked me to investigate alternatives to Cisco IP Phones for our IPT implementation.We currently have standardised on 794x or 7912 models, however, these are now relatively expensive due to the $ to £ exchange rate.I'd like to...
I've got a bit of a problem with my UC500. It's not in production yet, so it's only a bit of a problem.I have my main number set up to go straight to Auto Attendant at ext 801. The AA is only configured as defaults. All calls that come into my mai...
Hi All,I have been asked to check the status of the IP Phone 7960G. Can you please provide the details to verify the same.Thanks
Hi I am using CCM 4.1(3). I have 2 auto attendant console clients running cluster wide. Both were working fine but today one of the client is keep giving problem. While trying to run the client it says "connecting to server" and stays there forever w...
hi all,i have got requirement from customer its almost same like Meet-me conference but actually it is not .....let me explain scenario .....there is a hunt pilot number e.g. 1000 which is bind with 4 extensions i.e. 1001 1002 1003 1004. ok. some one...
I need help with a problem, occuring more or less since our last CM Upgrade from 5.2 to 6.1.2Phones(7961, 7911) don't assume changes like locale changes and new added expansion modules(7914).The Phones are resetting normally but afterwards the locale...
